Netgear D6200 Manual Do Utilizador
NETGEAR genie ADVANCED Home
52
D6200 WiFi DSL Modem Router
-
RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
Use Router as DHCP Server
This check box is selected so that the WiFi DSL modem router functions as a Dynamic Host
Configuration Protocol (DHCP) server.
Configuration Protocol (DHCP) server.
•
Starting IP Address. Specify the start of the range for the pool of IP addresses in the
same subnet as the WiFi DSL modem router.
same subnet as the WiFi DSL modem router.
•
Ending IP Address. Specify the end of the range for the pool of IP addresses in the
same subnet as the WiFi DSL modem router.
same subnet as the WiFi DSL modem router.
52.
Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer receives
the same IP address each time it accesses the WiFi DSL modem router’s DHCP server.
the same IP address each time it accesses the WiFi DSL modem router’s DHCP server.
Assign reserved IP addresses to servers that require permanent IP settings. For more
information, see
53.
Use the WiFi DSL Modem Router as a DHCP Server
By default, the WiFi DSL modem router functions as a DHCP server, allowing it to assign IP,
DNS server, and default gateway addresses to all computers connected to the WiFi DSL
modem router’s LAN. The assigned default gateway address is the LAN address of the WiFi
DSL modem router. The WiFi DSL modem router assigns IP addresses to the attached
computers from a pool of addresses specified in this screen. Each pool address is tested
before it is assigned to avoid duplicate addresses on the LAN. For most applications, the
default DHCP and TCP/IP settings of the WiFi DSL modem router are satisfactory.
DNS server, and default gateway addresses to all computers connected to the WiFi DSL
modem router’s LAN. The assigned default gateway address is the LAN address of the WiFi
DSL modem router. The WiFi DSL modem router assigns IP addresses to the attached
computers from a pool of addresses specified in this screen. Each pool address is tested
before it is assigned to avoid duplicate addresses on the LAN. For most applications, the
default DHCP and TCP/IP settings of the WiFi DSL modem router are satisfactory.
You can specify the pool of IP addresses that are assigned by setting the starting IP address
and ending IP address. These addresses should be part of the same IP address subnet as
the WiFi DSL modem router’s LAN IP address. Using the default addressing scheme, you
should define a range between 192.168.0.2 and 192.168.0.254, although you might want to
save part of the range for devices with fixed addresses.
and ending IP address. These addresses should be part of the same IP address subnet as
the WiFi DSL modem router’s LAN IP address. Using the default addressing scheme, you
should define a range between 192.168.0.2 and 192.168.0.254, although you might want to
save part of the range for devices with fixed addresses.
The WiFi DSL modem router delivers the following parameters to any LAN device that
requests DHCP:
requests DHCP:
•
An IP address from the range that you have defined
•
Subnet mask
•
Gateway IP address (the WiFi DSL modem router’s LAN IP address)
•
DNS server IP address (the WiFi DSL modem router’s LAN IP address)
To use another device on your network as the DHCP server, or to manually configure the
network settings of all of your computers, clear the Use Router as DHCP Server check box
and click Apply. Otherwise, leave this check box selected. If this service is not enabled and
network settings of all of your computers, clear the Use Router as DHCP Server check box
and click Apply. Otherwise, leave this check box selected. If this service is not enabled and