ONKYO TX-NR801 Manual De Instruções

21

Connecting to Audio/Video Equipment—Continued

For other models:
Note that the OSD Menu data will be output to the 
MONITOR OUT VIDEO, S VIDEO and 
COMPONENT VIDEO jacks. When you connect any 
OSD-specific monitor TV to the VIDEO connectors, you 
can disable the OSD output to COMPONENT VIDEO 
OUTPUT. To disable the OSD output, select Setup 
Menu 

→ Preference → OSD Setup → Component 

Video, and then select “OSD Off” (See page 63).

Using an RCA video connection cable, connect the 
video output jack (composite) of the DVD or LD player 
to the DVD VIDEO IN jack of the TX-NR801/
TX-NR801E. Or if the DVD or LD player has an S video 
output jack, connect it to the DVD S VIDEO IN jack 
with an S video connection cable. Or if the device has 
component video outputs, connect them to one of the 
banks of COMPONENT VIDEO INPUT jacks on the 
TX-NR801/TX-NR801E.
On the initial settings of the TX-NR801/TX-NR801E, 
the DVD input source is set for the COMPONENT 
VIDEO INPUT 1 jacks.
If you connect the DVD or LD player to the 
COMPONENT VIDEO INPUT 2 jacks, this must be 
changed at Setup Menu 

→ Input Setup → Video Setup 

→ Component Video (See page 38).
Using an RCA audio connection cable, connect the 
audio output jacks of the DVD or LD player to the DVD 
AUDIO IN jacks of the TX-NR801/TX-NR801E. Make 
sure that you properly connect the left channel to the L 
jack and the right channel to the R jack.
If the device has a digital output, connect it to either the 
DIGITAL IN COAX jack or DIGITAL IN OPT jack of 
the TX-NR801/TX-NR801E, depending on the type of 
connector on the DVD player.
On the initial settings of the TX-NR801/TX-NR801E, the 
DVD input source is set for digital input at the COAX 1 jack.

If the digital connection is made at a different jack, this 
must be changed at Setup Menu 

→ Input Setup → 

Digital Setup (See page 36).
Make sure of your DVD player’s digital output settings. 
You need to access the On Screen Menu of your DVD 
player. See the owner’s Manual on your DVD player.
Also,  you need to aware of the Table of contents for the 
movie, selecting the movie for Dolby Digital or DTS, 
depends how the movie is encoded.

Using RCA video connection cables, connect the video 
output jack (composite) of the video cassette recorder to the 
VIDEO 1 VIDEO IN jack of the TX-NR801/TX-NR801E 
and connect the video input jack of the video cassette 
recorder to the VIDEO 1 VIDEO OUT jack of the 
TX-NR801/TX-NR801E. Or if the video cassette recorder 
has S video input and output jacks, connect them to the 
VIDEO 1 S VIDEO IN and OUT jacks of the TX-NR801/
TX-NR801E using S video connection cables. Or if the 
video cassette recorder has component video outputs, 
connect them to one of the banks of COMPONENT 
VIDEO INPUT jacks on the TX-NR801/TX-NR801E.

On the initial settings of the TX-NR801/TX-NR801E, 
the VIDEO 1 input source is set for the 
COMPONENT VIDEO INPUT 2 jacks.
If you connect the video cassette recorder to the COMPONENT 
VIDEO INPUT 1 jacks, this must be changed at Setup Menu 

→ 

Input Setup 

→ Video Setup → Component Video (See page 38).

Using RCA audio connection cables, connect the audio 
output jacks of the video cassette recorder to the VIDEO 1 
AUDIO IN jacks of the TX-NR801/TX-NR801E and 
connect the audio input jacks of the video cassette recorder to 
the VIDEO 1 AUDIO OUT jacks of the TX-NR801/
TX-NR801E. Make sure that you properly connect the left 
channels to the L jacks and the right channels to the R jacks.