ONKYO TX-NR801 Manual De Instruções

87

Letting the Remote Controller Learn the Codes from Other Remote 
Controllers—Continued

Notes:
• The remote controller codes for Onkyo compact disc 

players, cassette tape decks, DVD players, and mini 
disc recorder have already been programmed into 
buttons on the remote controller. You may, however, 
use these buttons to program the codes for other 
remote controllers. If you wish to restore the Onkyo 
preset codes after you program new codes, you must 
first erase the new codes (See this page).

• The remote controller has 408 memory slots (8 

modes 

× 51 buttons). Some remote controllers may 

have more commands than can be remembered by the 
remote controller. In such cases, it will be necessary 
for you to determine which commands are more 
important to you.

• If the SEND/LEARN indicator quickly flashes three 

times and turns off, then the remote controller has 
exited the programming mode because either you 
have made a mistake during programming or a time-
out has occurred because no button was pressed. 
Resume from Step 2.

• If you try to program beyond the learning capacity of 

the remote controller, the SEND/LEARN indicator 
flashes six times quickly, and the remote controller 
exits the programming mode. Try programming 
under a different MODE button.

• When you want to program a command to a button to 

which you have already programmed a command, sim-
ply follow the same procedure given and the previous 
programming for that button will be overwritten.

• The remote controller uses infrared rays to send its 

commands, as do most other remote controllers. 
Though most remote controller codes can be memo-
rized by the remote controller, be aware that some 
remote controllers use systems that are quite different 
from the remote controller and therefore may not be 
able to be programmed.

• Some remote controllers have a single button that 

performs multiple functions (for example, the func-
tion may change each time the button is pressed). If 
this is the case, each function must be programmed to 
a separate button on the remote controller.

• Once you have transferred the commands from the 

other remote controller, refer to the instruction man-
ual that came with that product for instructions on 
how to operate that product.

• Make sure both the remote controller and the other 

remote controller have new batteries. If either of them 
has batteries that are low, you may not be able to pro-
gram the commands of the other remote controller 
properly into the remote controller.

You can only erase memorized commands and not preset ones.

Note:
If no button is pressed for more than 30 seconds during 
the erasing procedure, the SEND/LEARN indicator 
flashes three times quickly, and the remote controller 
exits the erasing mode. Resume from Step 1.

Notes:
• If no button is pressed for more than 30 seconds dur-

ing the erasing procedure, the SEND/LEARN indica-
tor flashes three times quickly and the remote 
controller exits the erasing mode. Resume from Step 1.

• If you perform an invalid operation during erasing, 

the SEND/LEARN indicator flashes three times 
quickly, and the remote controller exits the erasing 
mode. Resume from Step 1.

• If many commands have been programmed to the 

MODE button, then the SEND/LEARN indicator 
may remain lit for up to 20 seconds during Step 2. 
This is not a malfunction.

Press and hold down the MODE button for 
the command, press the ENTER/ZONE 2 
button, and then release both buttons.
When you press the MODE button, the SEND/
LEARN indicator lights. When you press the 
ENTER/ZONE 2 button, the lamp turns off. When 
you release the buttons, the lamp lights again.

Press and release the button for the com-
mand you wish to erase.
When you press the button, the SEND/LEARN 
indicator turns off. When you release the button, 
the lamp lights again.

Press and release the same button again.
The SEND/LEARN lamp slowly flashes twice. 
The memorized command is erased.

Press and hold down the desired MODE 
button, press the ENTER/ZONE 2 button 
twice, and then release both buttons.
When you press the MODE button, the SEND/
LEARN indicator lights. When you press the 
ENTER/ZONE 2 button, the lamp turns off. 
When you release the buttons, the lamp slowly 
flashes twice and then lights again.

Press and release the same MODE button 
again.
When you release the button, the SEND/LEARN 
indicator slowly flashes twice. This erases all the 
commands memorized to the MODE button.