Compustar model p1bamr Manual Do Utilizador
5
Active Lock/Arm and Unlock/Disarm
Tap the single button for 1 second to lock/arm and unlock/disarm. The remote bright blue LED
will flash four times indicating the signal has been sent to the vehicle.
will flash four times indicating the signal has been sent to the vehicle.
This feature is optional
and may require additional programming and/or installation. Please check with your dealer for details.
Automatic Transmission Remote Start Function
Hold the single button
for 3.5 seconds to remote start an automatic transmission vehicle. If you are in
range and if the vehicle is ready to remote start, the vehicle parking lights will flash once.
If you are in range, the parking lights on the vehicle will flash three times followed by a certain number
after that, there is a remote start error. Refer to the “remote start error diagnostic” on the last
If you are in range, the parking lights on the vehicle will flash three times followed by a certain number
after that, there is a remote start error. Refer to the “remote start error diagnostic” on the last
page of this
manual for details.
Upon receiving confirmation that your vehicle is running, the parking lights will light solid. The remote-
start run-time can be programmed for 3, 15, 25, or 45 minutes - ask your local CompuStar dealer to
adjust Option 2-7 if you would like a run-time other than 15 minutes (default).
IMPORTANT: The vehicle’s key must be inserted into the ignition and turned to the “on” position prior to
driving your vehicle. If the foot brake is depressed prior to the key being in the “on” position, the vehicle
will shut off.
Upon receiving confirmation that your vehicle is running, the parking lights will light solid. The remote-
start run-time can be programmed for 3, 15, 25, or 45 minutes - ask your local CompuStar dealer to
adjust Option 2-7 if you would like a run-time other than 15 minutes (default).
IMPORTANT: The vehicle’s key must be inserted into the ignition and turned to the “on” position prior to
driving your vehicle. If the foot brake is depressed prior to the key being in the “on” position, the vehicle
will shut off.
Manual Transmission Remote Start Function (Reservation Mode)
In order to remote start a manual transmission vehicle, the system must first be set in Reservation Mode.
Reservation Mode must be set each and every time you want to remote start a manual transmission
vehicle. The purpose of Reservation Mode is to leave the transmission in neutral before exiting the
vehicle.
IMPORANT:
Reservation Mode must be set each and every time you want to remote start a manual transmission
vehicle. The purpose of Reservation Mode is to leave the transmission in neutral before exiting the
vehicle.
IMPORANT:
• The transmission must be left in the neutral position.
• The vehicles windows must be rolled up.
• The vehicles door pins must be in working order.
• Do not install this remote start on a manual transmission vehicle that has a convertible or
removable top.
• Do not set reservation mode or remote start with people in the vehicle.
Activating Reservation Mode
STEP 1: While the vehicle is running, place the transmission in neutral, set the emergency / parking
brake, and remove pressure from the foot brake.
STEP 2: Remove the key from the vehicle’s ignition. The vehicle’s engine should remain running even
after the key has been removed. If the vehicle does not remain running visit your local authorized
CompuStar dealer for service.
STEP 3: Exit the vehicle and close the door. The vehicle’s engine should shut off within upon closing the
last door. If the vehicle’s engine does not shut off, your door trigger may be functioning improperly. Do
not use the remote-start feature and take your vehicle to a local authorized CompuStar dealer for
service.
IMPORTANT: By default, the system will lock/arm the vehicle upon setting reservation mode. Take care
to not lock your keys inside the vehicle.
brake, and remove pressure from the foot brake.
STEP 2: Remove the key from the vehicle’s ignition. The vehicle’s engine should remain running even
after the key has been removed. If the vehicle does not remain running visit your local authorized
CompuStar dealer for service.
STEP 3: Exit the vehicle and close the door. The vehicle’s engine should shut off within upon closing the
last door. If the vehicle’s engine does not shut off, your door trigger may be functioning improperly. Do
not use the remote-start feature and take your vehicle to a local authorized CompuStar dealer for
service.
IMPORTANT: By default, the system will lock/arm the vehicle upon setting reservation mode. Take care
to not lock your keys inside the vehicle.