Axiom Manufacturing Inc 0511AXM0361 Manual Do Utilizador
MC13192U Transceiver Module
User Guide
3
Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the
shunt, no 2 pins are connected, or jumper is removed. It is recommended that
the jumpers be placed idle by installing on 1 pin so they will not be lost.
shunt, no 2 pins are connected, or jumper is removed. It is recommended that
the jumpers be placed idle by installing on 1 pin so they will not be lost.
Signal names in this document that are followed by an asterisk (*) denote an active-low
signal.
signal.
Module Features
The MC13192U Transceiver module is a low cost demonstration or application module
for the Freescale MC13192 Zigbee
for the Freescale MC13192 Zigbee
™ capable transceiver device. Module operation is
controlled by any host microcontroller with a Serial Peripheral Interface (SPI) port.
Interface connections are compatible with several Freescale microcontroller DEMO and
EVB development boards. Development of applications for several microcontrollers is
quick and easy with the included demonstration example software.
Interface connections are compatible with several Freescale microcontroller DEMO and
EVB development boards. Development of applications for several microcontrollers is
quick and easy with the included demonstration example software.
♦ MC13192
Transceiver
* SPI interface
* 2.4GHz RF operation
* Optional clock output 32KHz to 8MHz (JP2)
* 2.4GHz RF operation
* Optional clock output 32KHz to 8MHz (JP2)
♦ 16Mhz
reference
Crystal
♦ On Board “F” antenna with TX/RX switch
♦ SMA test jack connection
♦ Regulated +3.0V power supply
♦ SPI Slave operation, 2 optional chip selects (JP1).
♦ J1 I/O connector standard, 2x12 R/A pins
MCU DEMO module or SLK series compatible
♦ J2_GP PORT connector optional, 2x 15 R/A pins
M68EVB9S08GB60 board compatible
♦ Power ON Indicator
♦ Size: 2 x 2.1 inches with 2 x 4-40 size mounting holes
♦ +3.3V to +5.5V input supply on I/O connector
♦ I/O Level translation for 3.3 to 5V systems
♦ 60ma maximum with TX on.
♦ FCC registered when applied with provided software examples.
♦ Supplied in Module pairs with Documentation (CD),
User Manual, and SMAC example software
The MC13192U provides a low cost method to apply RF communication to any system.
Supporting application software examples are available for Freescale Coldfire
Supporting application software examples are available for Freescale Coldfire
™,
HC(S)12, and HCS08 targets. Modules are provided in pairs in the standard kit and are
certified with the FCC for application in other systems.
certified with the FCC for application in other systems.
Standard installation places module at 90 degrees vertical to controller or host platform.
Versatile connection to host controller boards will allow stacking in different
configurations or connection by ribbon cable, contact Axiom with special requirements.
Module applies an embedded antenna and derives the 3.3V to 5.5V DC input power
from the supporting host platform so no other accessories are required. Mounting holes
are provided opposite from the connector to secure the module if required, 4-40 size
nylon hardware should be applied for this purpose.
Versatile connection to host controller boards will allow stacking in different
configurations or connection by ribbon cable, contact Axiom with special requirements.
Module applies an embedded antenna and derives the 3.3V to 5.5V DC input power
from the supporting host platform so no other accessories are required. Mounting holes
are provided opposite from the connector to secure the module if required, 4-40 size
nylon hardware should be applied for this purpose.
MC13192U