ADC Telecommunications Inc. PSM7A7UD Manual Do Utilizador
Understanding the RF Module Cables
Page 16
FlexWave Prism RF Modules for Prism Remote Units Installation Guide
© 2013 TE Connectivity Ltd
TECP-77-141 Issue 5 • 300001744178 Rev E • November 2013
RF Cable Rules
•
When installing a Diversity, MIMO or Dual‐Band RF Module, both RF cables labeled MOD N
TX0/RX0 and MOD N TX1/RX1 shall be connected to the N‐Style connections of the RF
Module.
TX0/RX0 and MOD N TX1/RX1 shall be connected to the N‐Style connections of the RF
Module.
•
When installing a Non‐Diversity or SISO RF Module:
–
The MOD N TX0/RX0 cable shall be connected to the single available N‐Style RF
Connection of the RF Module.
Connection of the RF Module.
–
The MOD N TX1/RX1 cable shall be constrained to the existing cables using a tie wrap or
similarly accepted fastener so it cannot be pinched or prevent the PRU door from closing.
Do not cut or attempt to otherwise remove this RF Cable.
similarly accepted fastener so it cannot be pinched or prevent the PRU door from closing.
Do not cut or attempt to otherwise remove this RF Cable.
•
RF cables are hand‐formable; however, cables must adhere to a minimum bend radius of
1‐inch from the outlet of the integrated cable guide to the respective N‐Style RF connection
on the RF Module.
1‐inch from the outlet of the integrated cable guide to the respective N‐Style RF connection
on the RF Module.
RF Module Cables for Single‐Card, Dual‐Card, and HDM RF Modules
The RF cable and connector labels also correspond to the RF Module slots in the PRU chassis,
where
where
MOD A
is the bottom slot and
MOD D
is the top slot. In the installation steps, the RF cables
and connectors are referred to as
MOD N TX0/RX0
and as
MOD N TRX1
where
N
equals
A
,
B
,
C
, or
D
.
The cables and connectors have corresponding labels as shown in
for Single‐Card,
Dual‐Card, and HDM RF Modules.
Table 7. RF Antenna Labels for Single‐Card, Dual‐Card, and HDM RF Modules—From Top of Chassis Down
RF Module
Cable,
RF Module
Connector,
Connector,
and Remote
Antenna
Connector
Label
Function
Single-Slot
Remote Unit RF
Module Slot
Designations
Dual-Slot Remote Unit RF Module Slot
Designations
Dual-Bay
Tri-Bay
Quad-Bay
Mod D
TX0/RX0
TX0/RX0
Transmit RF power and primary receive
to/from the antenna for RF Module D
to/from the antenna for RF Module D
MOD D
N/A
N/A
MOD C
Mod D
TX1/RX1
TX1/RX1
Diversity receive for RF power from the
antenna for RF Module D
antenna for RF Module D
Mod C
TX0/RX0
TX0/RX0
Transmit RF power and primary receive
to/from the antenna for RF Module C
to/from the antenna for RF Module C
MOD C
N/A
MOD B
Mod C
TX1/RX1
TX1/RX1
Diversity receive for RF power from the
antenna for RF Module C
antenna for RF Module C
Mod B
TX0/RX0
TX0/RX0
Transmit RF power and primary receive
to/from the antenna for RF Module B
to/from the antenna for RF Module B
MOD B
MOD A
MOD B
Mod B
TX1/RX1
TX1/RX1
Diversity receive for RF power from the
antenna for RF Module B
antenna for RF Module B
Mod A
TX0/RX0
TX0/RX0
Transmit RF power and primary receive
to/from the antenna for RF Module A
to/from the antenna for RF Module A
MOD A
MOD A
MOD A
Mod A
TX1/RX1
TX1/RX1
Diversity receive for RF power from the
antenna for RF Module A
antenna for RF Module A