Справочник Пользователя для Procom EL250RYLB-O

Скачать
Страница из 21
  1 0
         WARNING:   Failure  to  position
the  parts  in  accordance  with  these
diagrams may  result  in  property
damage  or  personal  injury.
         CAUTION:    After  installation and
periodically  thereafter,  check  to en-
sure  that  no  flame  comes  in
contact   with  any  log.  With  the  heater
set  to  HIGH, check  to  see  if  flames
contact  any  log. If  so, reposition  logs
according  to the log  installation
instructions  in  this  manual. Flames
contacting  logs  will  create  soot.
INSTALLING  LOGS
Figure  10 -Installing  Log  Set (Top
View)
INSTALLATION
Continued
IMPORTANTMake  sure  log  does not
cover any burner ports (see Figure10).
OPERATING    HEATER
FOR   YOUR   SAFETY 
READ   BEFORE
LIGHTING
              WARNING:   If  you  do not
follow  these  instructions  exactly, a fire
or  explosion  may  result  causing prop-
erty  damage, personal injury or
loss  of  life.
A.  This  appliance  has  a  pilot  which
must  be  lighted by control system,
When lighting  the  pilot, follow
t h e s e   i n s t r u c t i o n s     e x a c t l y .
B. BEFORE LIGHTING smell all
around  the  appliance  area  for
gas. Be sure to smell next  to the
floor  because  some  gas  is
heavier  than  air  and  will  settle
on  the  floor.
WHAT  TO  DO   IF  YOU  SMELL GAS
SEE WARNING in Page 1 for proper
instructions.
C.   Use only your hand to  push  in  control
       knob. Never use tools. If  the the appli-
       ance could not operate , don't  try  to re
      pair it, Call a qualified service technician
      or gas supplier.Forced or  attempted  re-
      pair may result   in  a fire or explosion.
D.    Do  not  use  this  appliance  if  any part
       has   been   under  water. Immediately
       call  a  qualified  service  technician  to
       inspect   the appliance  and  to  replace
       any part of  the  control system and  any
       gas  control   which  has   been  under
       water.
  TO TURN OFF GAS TO APPLIANCE
  Shut off heater
1. Press the IGN/OFF button.(see fig 12)
2. Set  the Switch on OFF location.(see fig 11)
  Shutting off burner only( pilot stay lit)
 1.Press the BURNER to set flame OFF se-
lect
 
 
 
 
 
 Fig 12-Front  of the Transmitter
         NOTICE:   During initial  operation  of
new  
fireplace
,  burning logs  will  give  off
a  paper-burning smell. Orange  flame
will  also  be present. Open  a  window  to
vent  smell. This  will  only  last  a  few
hours.
         CAUTION:  Do not  try  to adjust heat-
i n g     l e v e l s     b y     u s i n g     t h e
equipment  shutoff  valve.
LIGHTING INSTRUCTIONS
1.    STOP! Read  the safety information,
        page  3.
2 .     M a k e   s u r e     e q u i p m e n t     s h u t o f f
valve  is  fully  open.
Figure  11 -Emergency Button  and
ON/OFF Switch Location
If  your remote transimitter is lost or mis-
placed , you can press the emergency
button to operate heater  manually  on or
off (see fig 11)