Справочник Пользователя для Procom EL250RYLB-O

 Press BURNER button, the flame        is
on “MAN” select.  At this selection, the
main burner will keep working no matter
what the temperature is set at. If there is a
need to shut off the main burner, just
press the “BURNER” button to make the

burner       on the “OFF” select.

the

main burner is on  “OFF” selection,.The
main burner will shut off.

1.Auto on:

when the burner is in a state of
readiness. Transmitter and burner is off.
Press TIMER button. Then press 

¡ø

¡ø

¡ø

¡ø

¡ø

 or

¨‹

¨‹

¨‹

¨‹

¨‹

change to the scheduled time, then press
the TIMER button again, the TIMER starts
timing and the TIMER is flashing and the
operation light(green)  begin flashing.
When the timer goes on the scheduled
time, the burner opens automatically.

2.Auto off:

when the burner is in operation, press
TIMER button. Then press 

¡ø

¡ø

¡ø

¡ø

¡ø

 or

¨‹

¨‹

¨‹

¨‹

¨‹

 to

change to the scheduled time, then press
the TIMER button again, the TIMER starts
timing and the TIMER is flashing and the
operation light(green) begin flashing.
When the timer goes on the scheduled
time, the burner closes automatically.
(See Fig 14)

1.Manual turn-off: when the heater is in
operation, press the ING/OFF button to
shut off the heater.

2.Auto turn-off: refer to the second step of
“Operations of Timing”

1.Plug-in 110V electrical outlet, you will

hear a high pitch sound 

and power light

(red)  on the door will be lit 

that indicates

that  the burner is ready to be operated.

Before plugging in the outlet make sure

that the appliance is connected to the gas

supply, then continue to the next step.

2.Point directly the remote transmitter to

the burner. Press ING/OFF button, the

electric spark starts igniting the pilot

 and

operation light (green) on the door will be lit

.

Wait five (5) minutes  to  clear out any air.

If  you smell  gas. STOP! Please check

the gas connection.

   There are three selections: “AUTO”

“MAN” and “OFF”

 

Press BURNER button, the  flame

is on “AUTO” select. Press

¡ø

¡ø

¡ø

¡ø

¡ø

 or

¨‹

¨‹

¨‹

¨‹

¨‹

to set

temperature. If the room  temperature is
two degree  lower than the set tempera-
ture on the remote,  the main burner will
turn on until the surrouding temperature
is two degree higher than the set
temperature. Once it reaches temperature
on the remoter, the main burner will
automatically shut off.

(Note: on the auto select  of main burner,

the main burner  does not respond  imm-

ediately to the set temperature until about
one minute later.)

          

           

1.Install three AAA  SIZE batteries in the bat-

tery holder.

The initial start-up on the LCD  is: SET TEMP

is 77°F, ROOM TEMP is 77°F, clock is AM12:

00, burner is on “OFF” select, and fan is on

“AUTO” select. Divide Points

 

of hour and

minute are flashing (i.e. the timer is
operating).

2.Clock setting: Press CLOCK button on the

remote transmitter panel to select item

(hour, minute). The selected item is

flashing. Press 

¡ø

¡ø

¡ø

¡ø

¡ø

 

 

 

 

 

o

o

o

o

o

r

r

r

r

r

¨‹

¨‹

¨‹

¨‹

¨‹

to change to the

correct actual hour(s); Press 

¡ø

¡ø

¡ø

¡ø

¡ø

 

 

 

 

 

o

o

o

o

o

r

r

r

r

r

¨‹

¨‹

¨‹

¨‹

¨‹

 

 

 

 

 

t

t

t

t

t

o

o

o

o

o

change to the correct minute(s), then press

CLOCK button again, time setting is

finished.

3. When in operation,   point the remote

transmitter to the remote receiver on the

burner in a maximum distance of 20 feet

without any obstruction  between them.