Справочник Пользователя для System Sensor DH500ACDC
available at most plumbing supply houses, may be
used. This flange/connector mounting technique
makes the initial installation easier because a 1-
inch to 1-1/4-inch hole may be drilled where the
flange/connector will be used. It is easier to push
the inlet tube through the larger hole.
used. This flange/connector mounting technique
makes the initial installation easier because a 1-
inch to 1-1/4-inch hole may be drilled where the
flange/connector will be used. It is easier to push
the inlet tube through the larger hole.
Modification Of Inlet Sampling Tubes
There may be situations where duct widths are not as
specified for the installation. In such cases, it is permissible
to modify an inlet sampling tube that is longer than neces-
sary to span the duct width.
There may be situations where duct widths are not as
specified for the installation. In such cases, it is permissible
to modify an inlet sampling tube that is longer than neces-
sary to span the duct width.
Use a 0.193-inch diameter (#11) drill and add the appro-
priate number of holes so that the total number of holes
exposed to the air flow in the duct is 10 to 12. Space the
additional holes as evenly as possible over the length of
the tube.
priate number of holes so that the total number of holes
exposed to the air flow in the duct is 10 to 12. Space the
additional holes as evenly as possible over the length of
the tube.
Step 5. Field Wiring
Wiring Installation Guidelines
All wiring must be installed in compliance with the
National Electrical Code and the local codes having juris-
diction, using the proper wire size(s). The conductors used
to connect smoke detectors to control panels and accessory
devices should be color-coded to reduce the likelihood of
wiring errors. Improper connections can prevent a system
from responding properly in the event of a fire.
Wiring Installation Guidelines
All wiring must be installed in compliance with the
National Electrical Code and the local codes having juris-
diction, using the proper wire size(s). The conductors used
to connect smoke detectors to control panels and accessory
devices should be color-coded to reduce the likelihood of
wiring errors. Improper connections can prevent a system
from responding properly in the event of a fire.
For signal wiring, (the wiring between interconnected
detectors or from detectors to auxiliary devices), it is rec-
ommended that single-conductor wire be no smaller than
18 gauge. The duct detector terminals accommodate wire
sizes up to 14 gauge. The last foot or so of conduit should
be flexible steel conduit (available in electrical supply
houses) which facilitates installation and puts less strain
on the conduit holes in the housing. Solid conduit connec-
tions may be used, if desired.
detectors or from detectors to auxiliary devices), it is rec-
ommended that single-conductor wire be no smaller than
18 gauge. The duct detector terminals accommodate wire
sizes up to 14 gauge. The last foot or so of conduit should
be flexible steel conduit (available in electrical supply
houses) which facilitates installation and puts less strain
on the conduit holes in the housing. Solid conduit connec-
tions may be used, if desired.
Smoke detectors and alarm system control panels have
specifications for allowable loop resistance. Consult the
control panel manufacturer’s specifications for the total
loop resistance allowed for the control panel being used
before wiring the detector loop.
specifications for allowable loop resistance. Consult the
control panel manufacturer’s specifications for the total
loop resistance allowed for the control panel being used
before wiring the detector loop.
Wiring Instructions
The DH500ACDC is designed for easy wiring. The housing
provides a terminal strip with clamping plates. Wiring con-
nections are made by stripping approximately 3/8-inch of
insulation from the end of the wire, sliding this bare end
under the plate, and tightening the clamping plate screw.
The DH500ACDC is designed for easy wiring. The housing
provides a terminal strip with clamping plates. Wiring con-
nections are made by stripping approximately 3/8-inch of
insulation from the end of the wire, sliding this bare end
under the plate, and tightening the clamping plate screw.
The DH500ACDC is built for 120/240 VAC or 24 VAC/DC
to operate auxiliary functions. See Figure 5A for operating
and wiring details.
to operate auxiliary functions. See Figure 5A for operating
and wiring details.
Notes on Jumper Wire J5 (See Figure 5A):
1. When the detector is used in a 4-wire application (relay
1. When the detector is used in a 4-wire application (relay
circuit is being used to control fans, dampers, etc.),
jumper wire J5, located between the two terminal strips
on the printed circuit board, must be cut to insure power
supply supervision.
jumper wire J5, located between the two terminal strips
on the printed circuit board, must be cut to insure power
supply supervision.
2. When the detector is used in a 2-wire application (relay
control is not being used for any control of fans, damp-
ers, etc.), jumper wire J5 must be left in place.
ers, etc.), jumper wire J5 must be left in place.
120/240 VAC Operation
To complete the wiring for 110/120 VAC operation, connect
the power supply wires to terminals 15 and 16 (see Figure
5A). If 220/240 VAC operation is preferred, connect the
power supply wires to terminals 16 and 17.
To complete the wiring for 110/120 VAC operation, connect
the power supply wires to terminals 15 and 16 (see Figure
5A). If 220/240 VAC operation is preferred, connect the
power supply wires to terminals 16 and 17.
24 VAC/DC Operation
To complete the wiring for 24 VAC or DC, connect the
power supply wires to terminals 7 and 8. Polarity is not
important.
To complete the wiring for 24 VAC or DC, connect the
power supply wires to terminals 7 and 8. Polarity is not
important.
Step 6. Install the Filters
Most duct installations are subject to dust accumulation.
System filters remove a large percentage of this contami-
nation, but cannot remove all of it. Dust inside the duct
detector causes problems. First, very fine particles of dust
can enter the detector sensing chamber and cause the unit
to alarm. Second, the accumulation of dust and dirt neces-
sitates a more frequent periodic cleaning schedule, which
can result in substantial cost and/or down time.
Disposable sampling tube filters can greatly reduce the
nuisance alarms caused by dust, and can also significantly
extend the maintenance interval. To install the sampling
tube filters, insert the filter adapter into the exhaust tube
and push the filter onto the adapter tube on the left, as
shown in Figure 6. Then, install the other filter over the
end of the inlet sampling tube.
Most duct installations are subject to dust accumulation.
System filters remove a large percentage of this contami-
nation, but cannot remove all of it. Dust inside the duct
detector causes problems. First, very fine particles of dust
can enter the detector sensing chamber and cause the unit
to alarm. Second, the accumulation of dust and dirt neces-
sitates a more frequent periodic cleaning schedule, which
can result in substantial cost and/or down time.
Disposable sampling tube filters can greatly reduce the
nuisance alarms caused by dust, and can also significantly
extend the maintenance interval. To install the sampling
tube filters, insert the filter adapter into the exhaust tube
and push the filter onto the adapter tube on the left, as
shown in Figure 6. Then, install the other filter over the
end of the inlet sampling tube.
CAUTION
Filters require periodic cleaning or replacement, depend-
ing on the amount of dust and dirt accumulated. Inspect
the filters at least quarterly – more often if dust accumula-
tion warrants it. Replacement filters can be ordered from
Notifier. (Exhaust tube/intake tube filter P/N F36-05-00.)
ing on the amount of dust and dirt accumulated. Inspect
the filters at least quarterly – more often if dust accumula-
tion warrants it. Replacement filters can be ordered from
Notifier. (Exhaust tube/intake tube filter P/N F36-05-00.)
Filters rarely have a significant effect on the behavior of
smoke. As a result, even a filter that is as much as 90%
clogged does not significantly affect the entry of smoke
into the duct detector housing. Therefore, visual inspection
is usually all that is necessary to determine if filters need
replacement.
smoke. As a result, even a filter that is as much as 90%
clogged does not significantly affect the entry of smoke
into the duct detector housing. Therefore, visual inspection
is usually all that is necessary to determine if filters need
replacement.
D500-07-00
5
I56-432-11R