Справочник Пользователя для Mitsubishi Electronics QD64D2
8
TROUBLESHOOTING
8.11 Action and Handling of Errors
8.11.1 Error code list
8
- 10
1
O
V
ER
VI
E
W
2
S
YST
EM
CONF
IGURA
T
ION
3
S
P
E
C
IF
ICA
T
IONS
4
P
R
O
C
EDURES
AND
S
E
T
T
INGS
B
E
F
O
RE
OP
E
R
A
T
ION
5
F
UNCT
IONS
6
UT
IL
IT
Y
P
A
CK
A
G
E
(
G
X
C
onfi
gurato
r-C
T
)
7
P
R
OGRA
M
MING
8
TR
O
U
BL
ESHO
O
T
IN
G
8.11
Action and Handling of Errors
8.11.1
Error code list
This section describes the descriptions and corrective actions for the errors detected by
the QD64D2.
the QD64D2.
Table 8.19 Error code list
Error
code
Description
Action
Operation at error
Error channel
Other channels
0
(Normal)
----
----
----
100
[Overflow error]
Perform the preset.
(Refer to Section 5.4.)
(Refer to Section 5.4.)
The linear counter
function stops
counting.
function stops
counting.
The error does
not affect other
channels.
not affect other
channels.
The present value (Un\G12 and 13) exceeded the
following range.
-2147483648 to 2147483647
(Only for the linear counter function)
following range.
-2147483648 to 2147483647
(Only for the linear counter function)
20m
[Continuous comparison No.m start point setting error]
Set a value from 1 to 16.
The continuous
comparison cannot
be started. (The
error does not
affect the other
continuous
comparison
number.)
comparison cannot
be started. (The
error does not
affect the other
continuous
comparison
number.)
The continuous comparison No.m start point setting
(Un\G50 and 100) is set to other than 1 to 16.
"m" indicates the continuous comparison number
where the error occurred.
(Un\G50 and 100) is set to other than 1 to 16.
"m" indicates the continuous comparison number
where the error occurred.
21m
[Continuous comparison No.m repeat point setting
error]
error]
Set a value from 1 to 16.
The continuous comparison No.m repeat point setting
(Un\G51 and 101) is set to other than 1 to 16.
"m" indicates the continuous comparison number
where the error occurred.
(Un\G51 and 101) is set to other than 1 to 16.
"m" indicates the continuous comparison number
where the error occurred.
22m
[Continuous comparison No.m ON time setting error]
Set a value from 1 to 10.
The continuous comparison No.m ON time setting
(Un\G52 and 102) is set to other than 1 to 10.
"m" indicates the continuous comparison number
where the error occurred.
(Un\G52 and 102) is set to other than 1 to 10.
"m" indicates the continuous comparison number
where the error occurred.
300
[Count enable execution not possible error]
Turn OFF the coincidence
output test command which is
ON.
output test command which is
ON.
The linear counter
function and ring
counter function
does not start
counting.
function and ring
counter function
does not start
counting.
The count enable command (Y06) is turned ON while
one of the following is ON.
•Coincidence output No.1 test command (Y0B)
•Coincidence output No.2 test command (Y0C)
one of the following is ON.
•Coincidence output No.1 test command (Y0B)
•Coincidence output No.2 test command (Y0C)