Справочник Пользователя для Intel SE7520JR2
Intel® Server Board SE7520JR2
Functional Architecture
Revision 1.0
C78844-002
35
IDE channels of the ICH5R. One channel is accessed through the 40-pin connector on the
baseboard. The signals of the second channel are routed to the 100-pin backplane connector
for use in either the Intel Server Chassis SR1400 or SR2400 when integrated with a backplane
for slim-line optical drive use.
baseboard. The signals of the second channel are routed to the 100-pin backplane connector
for use in either the Intel Server Chassis SR1400 or SR2400 when integrated with a backplane
for slim-line optical drive use.
3.2.3.3 SATA
Controller
The SATA controller supports two SATA devices, providing an interface for SATA hard disks
and ATAPI devices. The SATA interface supports PIO IDE transfers up to 16 Mb/s and Serial
ATA transfers up to 1.5 Gb/s (150 MB/s). The ICH5-R’s SATA system contains two independent
SATA signal ports. They can be electrically isolated independently. Each SATA device can have
independent timings. They can be configured to the standard primary and secondary channels.
and ATAPI devices. The SATA interface supports PIO IDE transfers up to 16 Mb/s and Serial
ATA transfers up to 1.5 Gb/s (150 MB/s). The ICH5-R’s SATA system contains two independent
SATA signal ports. They can be electrically isolated independently. Each SATA device can have
independent timings. They can be configured to the standard primary and secondary channels.
3.2.3.4
Low Pin Count (LPC) Interface
The ICH5-R implements an LPC Interface as described in the Low Pin Count Interface
Specification, Revision 1.1. The Low Pin Count (LPC) bridge function of the ICH5-R resides in
PCI Device 31:Function 0. In addition to the LPC bridge interface function, D31:F0 contains
other functional units including DMA, interrupt controllers, timers, power management, system
management, GPIO, and RTC.
Specification, Revision 1.1. The Low Pin Count (LPC) bridge function of the ICH5-R resides in
PCI Device 31:Function 0. In addition to the LPC bridge interface function, D31:F0 contains
other functional units including DMA, interrupt controllers, timers, power management, system
management, GPIO, and RTC.
3.2.3.5
Compatibility Modules (DMA Controller, Timer/Counters, Interrupt
Controller)
The DMA controller incorporates the logic of two 82C37 DMA controllers, with seven
independently programmable channels. Channels 0–3 are hardwired to 8-bit, count-by-byte
transfers, and channels 5–7 are hardwired to 16-bit, count-by-word transfers. Any two of the
seven DMA channels can be programmed to support fast Type-F transfers.
independently programmable channels. Channels 0–3 are hardwired to 8-bit, count-by-byte
transfers, and channels 5–7 are hardwired to 16-bit, count-by-word transfers. Any two of the
seven DMA channels can be programmed to support fast Type-F transfers.
The ICH5-R supports two types of DMA: LPC and PC/PCI. LPC DMA and PC/PCI DMA use the
ICH5-R’s DMA controller. The PC/PCI protocol allows PCI-based peripherals to initiate DMA
cycles by encoding requests and grants via two PC/PC REQ#/GNT# pairs. LPC DMA is handled
through the use of the LDRQ# lines from peripherals and special encoding on LAD[3:0] from the
host. Single, Demand, Verify, and Increment modes are supported on the LPC interface.
Channels 0–3 are 8 bit channels. Channels 5–7 are 16 bit channels. Channel 4 is reserved as a
generic bus master request.
ICH5-R’s DMA controller. The PC/PCI protocol allows PCI-based peripherals to initiate DMA
cycles by encoding requests and grants via two PC/PC REQ#/GNT# pairs. LPC DMA is handled
through the use of the LDRQ# lines from peripherals and special encoding on LAD[3:0] from the
host. Single, Demand, Verify, and Increment modes are supported on the LPC interface.
Channels 0–3 are 8 bit channels. Channels 5–7 are 16 bit channels. Channel 4 is reserved as a
generic bus master request.
The timer/counter block contains three counters that are equivalent in function to those found in
one 82C54 programmable interval timer. These three counters are combined to provide the
system timer function, and speaker tone. The 14.31818 MHz oscillator input provides the clock
source for these three counters.
one 82C54 programmable interval timer. These three counters are combined to provide the
system timer function, and speaker tone. The 14.31818 MHz oscillator input provides the clock
source for these three counters.
The ICH5-R provides an ISA-compatible Programmable Interrupt Controller (PIC) that
incorporates the functionality of two 82C59 interrupt controllers. The two interrupt controllers are
cascaded so 14 external and two internal interrupts are possible. In addition, the ICH5-R
supports a serial interrupt scheme. All of the registers in these modules can be read and
restored. This is required to save and restore the system state after power has been removed
and restored to the platform.
incorporates the functionality of two 82C59 interrupt controllers. The two interrupt controllers are
cascaded so 14 external and two internal interrupts are possible. In addition, the ICH5-R
supports a serial interrupt scheme. All of the registers in these modules can be read and
restored. This is required to save and restore the system state after power has been removed
and restored to the platform.