Справочник Пользователя для Panduit DPOE12U1XY
PANDUIT® DPoE™ Power Patch Panel User’s Guide
Issue 2.2
Part Number: PN378A
15
Table 6: DPoE™ Power Patch Panel Power Up Sequence
Behavior as viewed from the back of the unit
Behavior as viewed from the front of the unit
Both network status LEDs will light amber for two
seconds
seconds
The panel status Light-Emitting Diode (LED) will
light red for about 10 seconds. After that, a LED
test sequence of the port status LEDs will take
place, lighting each port status LED amber. It will
appear as if the port status LED is “walking” from
port 1 through port 24.
light red for about 10 seconds. After that, a LED
test sequence of the port status LEDs will take
place, lighting each port status LED amber. It will
appear as if the port status LED is “walking” from
port 1 through port 24.
If there is no cable connected to the IN
management port (Step 5 above), both network
status LEDs will turn off.
management port (Step 5 above), both network
status LEDs will turn off.
If the Patch Panel is configured for Dynamic Host
Control Protocol (DHCP) address assignment
(default configuration) and a cable is NOT
connected to the IN management port on the rear
of the panel, the panel status LED will turn green.
Control Protocol (DHCP) address assignment
(default configuration) and a cable is NOT
connected to the IN management port on the rear
of the panel, the panel status LED will turn green.
If the DPoE™ Power Patch Panel is configured
for DHCP address assignment (default factory
setting), the network status LED above the IN
management port will stay amber and the
network status LED above the OUT management
port will turn off. This indicates that the panel is
actively requesting address information from the
network. Once this information is received (this
could take up to a minute), the network status
LED above the IN management port will turn on
or start flashing green as data is transmitted and
received.
for DHCP address assignment (default factory
setting), the network status LED above the IN
management port will stay amber and the
network status LED above the OUT management
port will turn off. This indicates that the panel is
actively requesting address information from the
network. Once this information is received (this
could take up to a minute), the network status
LED above the IN management port will turn on
or start flashing green as data is transmitted and
received.
If the DPoE™ Power Patch Panel is configured for
DHCP address assignment (default factory setting),
the panel status LED will flash amber. This
indicates that the panel is actively requesting
address information from the network. Once this
information is received (this could take up to a
minute), the panel status LED will flash green. (See
page 5, Figure 1: DPoE™ Power Patch Panel
(Front View) and page 6, Figure 2: DPoE™ Power
Patch Panel (Rear View) for a graphical view of the
LEDs on the DPoE™ Power Patch Panel.)
DHCP address assignment (default factory setting),
the panel status LED will flash amber. This
indicates that the panel is actively requesting
address information from the network. Once this
information is received (this could take up to a
minute), the panel status LED will flash green. (See
page 5, Figure 1: DPoE™ Power Patch Panel
(Front View) and page 6, Figure 2: DPoE™ Power
Patch Panel (Rear View) for a graphical view of the
LEDs on the DPoE™ Power Patch Panel.)
If the panel were set to static IP addressing rather
than DHCP, the network status LED above the IN
management port will immediately turn green.
than DHCP, the network status LED above the IN
management port will immediately turn green.
If the panel were set to static IP addressing rather
than DHCP, the panel status LED will flash green
and continue flashing as long as power is applied
to the unit.
than DHCP, the panel status LED will flash green
and continue flashing as long as power is applied
to the unit.
Basic Troubleshooting
Use the following guide to help resolve problems installing the DPoE™ Power Patch Panel. If the problem
persists, contact PANDUIT Corp Technical Support or a local sales representative. (See page 9, Table 3:
PANDUIT Corporation Contact Information, for contact information.)
persists, contact PANDUIT Corp Technical Support or a local sales representative. (See page 9, Table 3:
PANDUIT Corporation Contact Information, for contact information.)