Справочник Пользователя для Behringer PMX3000

EUROPOWER PMX1000/PMX3000/PMX5000

2. CONTROL ELEMENTS

considerably higher than the power provided to the

speakers wired to the parallel speaker outputs.

Please read the information given on the rear panel

of the power mixer.

Information on how to properly connect your speaker

with regard to polarity can be found on the rear of

the unit (PIN assignment) (see also

and

PMX5000: Use the BEHRINGER SPEAKER PROCESSING

switch to activate a filter that allows you to adapt the mixer

to the characteristics of your loudspeakers. If the speakers

have a limited frequency response in the bass range, this

function allows you to filter this range at the output signal

of the mixer and thus adapt it optimally to the frequency

response of the speakers.

PMX1000/PMX5000:

If STANDBY is pressed, all input

channels are muted. During pauses you can prevent the

microphones from picking up noise or interference, which

would then be reproduced by the P.A. system or possibly

damage the speaker diaphragms. The benefit is that all

faders can be left untouched while you play back music

from CD via the CD/TAPE inputs (see

). There is also

no need to move the faders and lose your mix.

2.2 Equalizer and FBQ

Your power mixer features a graphic 7-band equalizer,

which allows you to fine-tune the sound depending on the

room acoustics. In the center position the frequency

response is not effected. To boost or cut a certain

frequency range, simply move the corresponding fader

upward or downward respectively.

Please note that the equalizer behaviour depends

on the position of the AMP MODE switch (see

Press the FBQ IN switch to activate the Feedback Detection

system (the FBQ will be active only if you have switched

on the equalizer

before). Frequencies causing

feedback are shown by brightly lit fader

LEDs. All other LEDs will be darker. Now,

cut the frequency range in question until

feedback disappears (the LED gets darker

or goes out). This function is available for

both the main and monitor mix.
PMX1000: The switch FBQ FEEDBACK DETECTION

performs the same function as on the PMX3000 and

PMX5000.
Use the MAIN/MON 1 switch to select whether the equalizer

processes the main or the monitor mix. When not pressed,

the stereo equalizer processes only the main mix. When the

switch is pressed, the EQ processes only the monitor mix.
PMX1000: The MAIN MIX/MONITOR switch performs the

same function as on the PMX3000 and PMX5000.
Press the EQ IN switch to activate the equalizer. The fader

LEDs illuminate when the EQ is on.
Use this LED display to control the output level of the main

signal. The upper LIM LED illuminates when the internal

amp protection circuit responds to levels that are too high.
PMX1000: The POWER LED is illuminated when you switch

the unit on.

The LIM LEDs and the LED display do NOT light up when

an external signal is fed in via the PWR AMP INSERT

jacks

2.3 Effects section

List of all multi-effects processor presets.
The LED level meter on the effects module should always

show a sufficiently high level. Make sure that the Clip LED

illuminates with signal peaks only. If it is constantly illu-

minated, the effects processor is overloading, which can

lead to unpleasant distortion. The

FX SEND fader

(PMX1000)

or FX/FX 1/2 fader (PMX3000/PMX5000) controls the level

sent to the effects module and to the FX SEND output

jacks.
The effects display always reads the currently selected

preset.
PMX3000/PMX5000: Press the FX1/2 IN switch to activate

the effects processor.
PMX1000/PMX3000: Turn the PROGRAM

control to select

an effects algorithm (preset number starts flashing). Press

this control to activate the effect selected.

PMX1000: The effects processor is operative all the

time. Adjust the effect intensity for the MAIN or

MON signals with controls

o r

respectively.

PMX5000: The PMX5000 has two separate effects

processors, which can be used independently of one

another. Enable one or both processors with the FX1/2 IN

buttons.

PMX3000/PMX5000: The FX 1/2 TO MON 1 control allows

you to set the intensity of the multi-effects processors in

the monitor mix. No effect is sent to the monitor mix when

this control is set fully counter-clockwise.
PMX1000: The FX TO MON control performs the same

function as on the PMX3000 and PMX5000.
The FX 1/2 TO MON 2 control allows you to determine the

effect intensity of the multi-effects processor in the monitor

2 mix. No effect is sent to the monitor 2 mix with this control

turned fully counter-clockwise.
The FX 1/2 TO MAIN control allows you to determine the

effect intensity of the multi-effects processor in the main

mix. No effect is sent to the main mix with this control

turned fully counter-clockwise.
PMX1000: The FX TO MAIN control performs the same

function as on the PMX3000 and PMX5000.

2.4 Main and monitor section

The SURROUND control determines the

effect intensity. This is a built-in effect, which

widens the stereo panorama, thus making

the sound more lively and transparent.

Press the XPQ TO MAIN switch to activate this effect.

Pressing the AFL switch (after-fader listening) activates

the solo function. If AFL is on for the corresponding channel

in the main section, you will only hear the signal from this

channel. Its volume can be adjusted with the fader.

Switching AFL on has no effect on the main or monitor mix,

as long as you dont move the fader. In this way, you can

monitor one or several selected signals via the PHONES/

CTRL jack

. When AFL is on, the corresponding control

LED illuminates.

The PMX1000 does not have an AFL function.
PMX1000: FX SEND fader.
PMX3000: FX fader.
PMX5000: FX 1/2 fader.
This is the master send fader for the signal routed to the

effects processor and to the FX SEND output

(see

also

and

PMX1000: MON SEND fader.
PMX3000/PMX5000: MON1/2 fader.
These faders are used to set the monitor output volume

(see also

and

PMX1000: The main mix allows you to control the volume

from the Main 1 output with both faders.
PMX3000/PMX5000: The MAIN 1 fader controls the volume

of the EUROPOWER. The main signal is also provided at the

MAIN 1 output (see also

PMX3000/PMX5000: The MONO fader controls the mono

mix signal (see also