Технические ссылки для Cisco Cisco 4100 Series Wireless LAN Controller
3/22/05
config 802.11b antenna
OL-7427-01 Rev 1
Syntax
config
Configure parameters.
802.11b
802.11b network parameters.
11gSupport
Support for the 802.11g network.
enable/disable
Enable or disable 802.11b/g.
<Cisco 1000 Series lightweight access point>To override the network setting
for individual <Cisco 1000 Series lightweight access
point> Cisco Radio.
point> Cisco Radio.
Defaults
Enabled.
Examples
>config 802.11b 11gSupport enable
Changing the 11gSupport will cause all the APs to reboot when you
Changing the 11gSupport will cause all the APs to reboot when you
enable 802.11b network.
Are you sure you want to continue? (y/n) n
11gSupport not changed!
Related Commands
show sysinfo, show 802.11b, config 802.11b enable, config wlan radio, config
802.11b disable, config 802.11a disable, config 802.11a enable
802.11b disable, config 802.11a disable, config 802.11a enable
config 802.11b antenna
config 802.11b antenna
To configure the 802.11b/g antenna, use the config 802.11b antenna command.
Use the config 802.11b disable command to disable the 802.11b/g Cisco Radio before using the config
802.11b antenna command. Then use the config 802.11b antenna command to configure the Cisco
1000 Series lightweight access point to use internal or external antennas. Then use the config 802.11b
enable command to enable the 802.11b/g Cisco Radio.
Use the config 802.11b disable command to disable the 802.11b/g Cisco Radio before using the config
802.11b antenna command. Then use the config 802.11b antenna command to configure the Cisco
1000 Series lightweight access point to use internal or external antennas. Then use the config 802.11b
enable command to enable the 802.11b/g Cisco Radio.
>
config 802.11b antenna <Cisco 1000 Series lightweight access point>
<internal/external>
Syntax
config
Configure parameters.
802.11b antenna
Antennas for 802.11b/g Cisco Radio.
<Cisco 1000 Series lightweight access point> Cisco 1000 Series lightweight
access point name.
<internal/external>
Configure for internal or external antennas.
Defaults
Internal.
Examples
>config 802.11b antenna AP1 internal
to set AP1 to use the 802.11b/g internal antennas.
to set AP1 to use the 802.11b/g internal antennas.
Related Commands
config 802.11b disable, config 802.11b enable, config 802.11a antMode
config 802.11b beaconperiod
config 802.11b beaconperiod
In Cisco SWAN 802.11b/g networks, all Cisco 1000 Series lightweight access point WLANs broadcast a
beacon at regular intervals. This beacon notifies clients that 802.11b/g service is available, and allows
the clients to synchronize with the Cisco 1000 Series lightweight access point. To change the 802.11b/
g beacon period for the whole 802.11b/g network, use the config 802.11b beaconperiod command.
Before you change the beacon period using the config 802.11b beaconperiod command, be sure that
you have disabled the 802.11b/g network using the config 802.11b disable command. When you are
done changing the beacon period, remember to enable the 802.11b/g network using the config
802.11b enable command.
beacon at regular intervals. This beacon notifies clients that 802.11b/g service is available, and allows
the clients to synchronize with the Cisco 1000 Series lightweight access point. To change the 802.11b/
g beacon period for the whole 802.11b/g network, use the config 802.11b beaconperiod command.
Before you change the beacon period using the config 802.11b beaconperiod command, be sure that
you have disabled the 802.11b/g network using the config 802.11b disable command. When you are
done changing the beacon period, remember to enable the 802.11b/g network using the config
802.11b enable command.
>
config 802.11b beaconperiod <Time Units>