Справочник Пользователя для Lennox elite epic-ck-lp

KIT CONTENTS (See Figure 1):

1 ea. Nova SIT NG Regulator Kit (A)

1 ea. #31 NG main burner orifice (40,000 BTU’s) (B)

1 ea. #36 NG main burner orifice (33,000 BTU’s) (C)

1 ea. Sticker “EPIC33” if NG orifice was #36

1 ea. Instruction Sheet

TOOLS NEEDED (See Figure 2):

5/32” Allen Wrench Or T-Handle Wrench

1/8” Allen Wrench Or T-Handle Wrench

Torx Bit (T20 with 1/4” shank and center hole)

1/2” Open End Wrench

7/16” Open End Wrench

EpIC™ GaS CONvErSION INSTruCTIONS Lp TO NG

CaT. NO. 75355, MODEL EpIC-CK-Lp TO NG

INSTaLLaTION INSTruCTIONS FOr CONvErTING FrOM prOpaNE GaS (Lp) TO
NaTuraL GaS (NG). FOr uSE wITh ThE EpIC DIrECT vENT GaS STOvE

775,235M

rev. C, 03/2008

HEARTH PRODUCTS

KITS AND ACCESSORIES

warNING

This conversion kit shall be installed by a qualified

service agency in accordance with the manufacturer's

instructions and all applicable codes and requirements

of the authority having jurisdiction. If the information

in these instructions is not followed exactly, a fire,

explosion or production of carbon monoxide may result

causing property damage, personal injury or loss of

life. The qualified service agency performing this

installation is responsible for the proper installation of

this kit and assumes responsibility for this conversion.

The installation is not proper and complete until the

operation of the converted appliance is checked as

specified in the manufacturers instructions supplied

with the kit.

IMpOrTaNT LE CaNaDa SEuLEMENT

La conversion devra être effectuée conformément

aux recommandations des autorités provinciales

ayant juridiction et conformément aux exigences

du code d'installation CaN/CSa B149.1 .

IMpOrTaNT CaNaDa

The conversion shall be carried out in accordance with

the requirements of the provincial authorities having

jurisdiction and in accordance with the requirements

of the CaN/CSa B149.1 Installation code.

avErTISSEMENT

Cet équipement de conversion sera installé par une

agence qualifiée de service conformément aux instruc-

tions du fabricant et toutes exigences et codes applica-

bles de l'autorisés avoir la juridiction. Si l'information

dans cette instruction n'est pas suivie exactement, un

feu, explosion ou production de protoxyde de carbone

peut résulter le dommages causer de propriété, perte

ou blessure personnelle de vie. L'agence qualifiée de

service est esponsable de l'installation propre de cet

équipment. L'installation n'est pas propre et compléte

jusqu'à l'opération de l'appareil converti est chéque

suivant les critères établis dans les instructions de

propriétaire provisionnées avec l'équipement.

IMpOrTaNT

The burner orifices provided in this kit are only for

use at elevations of 0 to 2,000 feet (610 M) in the

uSa and 0 to 4,500 feet (0-1372 M) in Canada. at

higher elevations the BTu input must be de-rated

by 4% for every 1,000 feet (305 M) to maintain

the proper ratio of gas to air. If the installer must

convert the unit to adjust for varying altitudes, a

deration information sticker must be filled out by the

installer and adhered to the appliance at the time

of the conversion. Contact your local gas supplier

for deration requirements for your area.

2-1

8-2

Fig. 2

Figure 1 - Kit Contents

Figure 2 - Tools Needed