Справочник Пользователя для myon AG M320-1
4
4
4
4 LED function indicators
LED function indicators
LED function indicators
LED function indicators
4.1
4.1
4.1
4.1 Transmitter
Transmitter
Transmitter
Transmitter
The transmitter indicates its state as described below:
•
When removing the transmitter from the charging cradle, the blue transmitter LED located
inside the housing will flash for about 2 minutes to signal the proper operation of the
transmitter .
inside the housing will flash for about 2 minutes to signal the proper operation of the
transmitter .
•
After about 2 minutes the transmitter LED is switched off.
Thus, during a measurement, there is no LED indication of transmitter operation
Thus, during a measurement, there is no LED indication of transmitter operation
during a measurement, there is no LED indication of transmitter operation
during a measurement, there is no LED indication of transmitter operation
during a measurement, there is no LED indication of transmitter operation. This
is to prevent the distraction of patients by simultaneous flashing of a relatively large
number of transmitter LEDs.
number of transmitter LEDs.
•
If during a measurement the remaining capacity of the built-in battery reaches a low value,
the transmitter's LED will begin to flash again. In this state further operation of the
transmitter is possible for a maximum of about 30 minutes before the transmitter will be
switched off automatically. The flashing frequency will be noticeably higher and it is
advisable to put the transmitter back into the charging cradle to reload its batteries.
the transmitter's LED will begin to flash again. In this state further operation of the
transmitter is possible for a maximum of about 30 minutes before the transmitter will be
switched off automatically. The flashing frequency will be noticeably higher and it is
advisable to put the transmitter back into the charging cradle to reload its batteries.
4.2
4.2
4.2
4.2 Receiver
Receiver
Receiver
Receiver
•
Within the receiver's enclosure there is one blue LED for each transmitted channel.
•
As soon as a wireless connection between a transmitter and the receiver has been
established successfully, the respective receiver LED will start flashing.
established successfully, the respective receiver LED will start flashing.
4.3
4.3
4.3
4.3 Charging cradle
Charging cradle
Charging cradle
Charging cradle
Each charging slot of the charging cradle features a single indicator LED located beneath the slot.
The indicator LED indicates three states:
The indicator LED indicates three states:
•
Battery is re-charging:
In this state, the charging slot indicator LED will flash at a low frequency, indicating that re-
charging of the transmitter's build-in battery is in progress. Please note, that re-charging
might take place from time to time even if the transmitter has not been used and stayed in
its slot in the charging cradle.
In this state, the charging slot indicator LED will flash at a low frequency, indicating that re-
charging of the transmitter's build-in battery is in progress. Please note, that re-charging
might take place from time to time even if the transmitter has not been used and stayed in
its slot in the charging cradle.
•
Battery has been re-charged:
After the transmitter's battery has been fully re-charged, the charging slot indicator LED is
illuminated constantly.
After the transmitter's battery has been fully re-charged, the charging slot indicator LED is
illuminated constantly.
•
Empty charging slot / transmitter not properly inserted:
If a charging slot is empty, the respective charging slot indicator LED will not light up. The
same happens if a transmitter has been inserted incorrectly into a charging slot and thus the
electrical contact between transmitter and charging cradle cannot be established.
If a charging slot is empty, the respective charging slot indicator LED will not light up. The
same happens if a transmitter has been inserted incorrectly into a charging slot and thus the
electrical contact between transmitter and charging cradle cannot be established.
Date: 03.06.2013
LaInMa-EU-m320 - Instructions manual (full version, english) - 20130603 - V1.7.odt
Page 14 of 32
V
E
R
S
IO
N
1
.7
/
0
3.
0
6
.2
0
13