Справочник Пользователя для Datastrip Inc. DSV2SC01
DSV2+
Turbo
User Manual, Version 1.09
43
Copyright © 2006 by Datastrip, Inc. All rights reserved.
Reproduction in whole or in part is prohibited.
16.2 ActiveSync via the Docking Station
16.2.1 Software/Hardware Requirements and Setup
•
ActiveSync version 3.7.1 or later installed on the host PC.
•
Docking station, docking station serial cable and Datastrip power adapter.
•
Connect the DB9 end of the Docking station serial cable to the PC COM1.
16.2.2 Establishing the Connection
•
Turn on the DSV2+ and when it has finished booting, place it in the docking cradle.
•
Each time you connect the DSV2+ terminal to the host PC you will be asked if you
would like to set up a Partnership. If you will be using this DSV2+ terminal on this PC
regularly then answer “Yes”. If this is a one time use on this PC answer “No”. In either
case you will be connected and can transfer files between the PC and the DSV2+
terminal.
regularly then answer “Yes”. If this is a one time use on this PC answer “No”. In either
case you will be connected and can transfer files between the PC and the DSV2+
terminal.
16.2.3 Disconnect
•
Disconnecting the ActiveSync cable or removing the DSV2+ terminal from the docking
cradle will disconnect the session on the PC side, but not on the DSV2+. Manually
disconnect the DSV2+ by clicking on the ActiveSync icon in the system tray and clicking
“Disconnect” or do nothing and the session will timeout after one minute. Both ends of
the connection must be disconnected before you can reconnect the cable and start another
ActiveSync session.
disconnect the DSV2+ by clicking on the ActiveSync icon in the system tray and clicking
“Disconnect” or do nothing and the session will timeout after one minute. Both ends of
the connection must be disconnected before you can reconnect the cable and start another
ActiveSync session.
16.2.4 Troubleshooting the Connection
If a connection is not automatically established check the following:
•
The DSV2+ will not connect while it is in Suspend mode. Wake the DSV2+ from
Suspend prior to placing it in the docking station.
•
Verify that “Serial via COM1” is selected on your terminal. Go to the Control Panel and
double click “PC Connection”. On this screen you should see “Serial via COM1”. If not
then click “Change Connection”. Click the scroll bar arrow. Select “Serial via COM1”
and click “OK”. Click “OK” again to close the PC Connection screen. Re-insert your
DSV2+ into the docking cradle to get connected.
then click “Change Connection”. Click the scroll bar arrow. Select “Serial via COM1”
and click “OK”. Click “OK” again to close the PC Connection screen. Re-insert your
DSV2+ into the docking cradle to get connected.
•
Place the DSV2+ in the docking cradle. On the PC, open the ActiveSync application and
select “File/Connection Settings”. Then select “Connect”. This will initiate a connection
with the DSV2+ from the PC side.
with the DSV2+ from the PC side.
16.3 ActiveSync via 802.11 CF Adaptor or Bluetooth USB Adaptor
16.3.1 Hardware/Software Requirements
The following materials are required to establish an ActiveSync connection via 802.11:
The following materials are required to establish an ActiveSync connection via 802.11:
•
A DSV2+ equipped with an 802.11 CF Adaptor or Bluetooth USB adapter.
•
A PC connected (wired or wirelessly) to an 802.11 wireless network.
•
ActiveSync version 3.7.1 or later installed on the host PC.
•
Docking station, docking station serial cable and Datastrip power adapter.
16.3.2 PC Configuration for 802.11
16.4 If connecting the DSV2+ to the host PC via 802.11 for the first
time, start by establishing a wired ActiveSync connection with the