Справочник Пользователя для Mitsubishi Electric Corp 485
Introduction
3
Reference page
AUDIO
VIDEO
OUT
OUT
IN
IN
RESET
ALM RST
IN
REC GND ALM MODE
CLK
OUT
CALL
BATTERY
OPEN
RS-485
ON
IN
OUT
TERMINATE
OFF
Rear View
Battery Box
Battery is stored here.
Battery is stored here.
Note
• This VCR contains a special battery. Consult your
dealer to replace it.
AUDIO IN connector
Audio input connector (RCA pin).
Audio input connector (RCA pin).
AUDIO OUT connector
Audio output connector (RCA pin).
Audio output connector (RCA pin).
VIDEO IN connector
Input connector for video signal (BNC connector).
Connect cameras here.
Input connector for video signal (BNC connector).
Connect cameras here.
VIDEO OUT connector
Output connector for video signal (BNC connector).
Connect a monitor here.
Output connector for video signal (BNC connector).
Connect a monitor here.
RESET button
page 37
RS-485 IN terminal (RJ-45 connector)
Input terminal to connect with a RS-485 controller.
Input terminal to connect with a RS-485 controller.
RS-485 OUT terminal (RJ-45 connector)
Output terminal to connect with other time lapse VCR
with RS-485 interface.
Output terminal to connect with other time lapse VCR
with RS-485 interface.
TERMINATE switch
Use to setup the termination (only when using the RS-
485 terminal).
ON : use to turn on the termination.
OFF : use to turn off the termination.
Use to setup the termination (only when using the RS-
485 terminal).
ON : use to turn on the termination.
OFF : use to turn off the termination.
For the rating of each connector at the rear panel of
VCR,
VCR,
page 34.
AC power socket
This socket connects to the power cord. Insert the
cord firmly.
This socket connects to the power cord. Insert the
cord firmly.
Input terminals
ALM IN
Use for alarm recording. The alarm sensor is
connected here.
RST IN
Use to stop alarm recording.
• When “ALARM REC DURATION” in
Use for alarm recording. The alarm sensor is
connected here.
RST IN
Use to stop alarm recording.
• When “ALARM REC DURATION” in
“RECORDING SET UP” menu is set to “MAN1,”
the alarm recording stops when a signal is input
to this terminal. The alarm reset switch is
connected here.
the alarm recording stops when a signal is input
to this terminal. The alarm reset switch is
connected here.
• When set to other than “MAN1,” it can be used to
adjust the VCR’s clock.
REC IN
Use to start/stop recording or for series recording.
Use to start/stop recording or for series recording.
GND
When a lead connected to other terminals requires a
ground, connect the ground lead here.
When a lead connected to other terminals requires a
ground, connect the ground lead here.
Output terminals
ALM OUT
Use to indicate an alarm recording to an external
alarm.
MODE OUT
Use to indicate the VCR’s mode of operation.
• When “MODE OUT” in “REAR TERMINAL” menu
Use to indicate an alarm recording to an external
alarm.
MODE OUT
Use to indicate the VCR’s mode of operation.
• When “MODE OUT” in “REAR TERMINAL” menu
is set to “CLOCK ADJ,” the clock of all connected
VCRs can be adjusted. (
VCRs can be adjusted. (
page 26)
CLK OUT
Use to control an external camera switcher.
CALL OUT
Use to indicate when a tape reaches its end during
recording or if there has been a problem during
recording.
Use to control an external camera switcher.
CALL OUT
Use to indicate when a tape reaches its end during
recording or if there has been a problem during
recording.
Warning:
The included power cord is used for 120 V, 60 Hz.
Never connect to any outlet or power supply having a different voltage or frequency.
Ensure the power cord is not plugged into the AC outlet before connecting to any rear terminals.
The included power cord is used for 120 V, 60 Hz.
Never connect to any outlet or power supply having a different voltage or frequency.
Ensure the power cord is not plugged into the AC outlet before connecting to any rear terminals.