Справочник Пользователя для Memorex Tek Partner Universal Remote Control
1. Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status
indicator (located to the left of the "1" button) lights up.
2. Press a desired Device Mode Button (e.g. "TV").
3. Use the number buttons to enter your 3-digit Device Code (from the Device Code List) for your
3. Use the number buttons to enter your 3-digit Device Code (from the Device Code List) for your
TV. The indicator should go out immediately. NOTE: The status indicator will not blink while
entering Device Codes in step 3 above.
entering Device Codes in step 3 above.
4. Turn on your device (e.g. TV), try the functions on the TEK PARTNER
TM
. If your device (e.g.
TV) responds to your requested function correctly, you have entered the correct Device Code.
Otherwise, repeat the above setup instructions with the remaining Device Codes until your device
(e.g. TV) responds to your requested function.
Otherwise, repeat the above setup instructions with the remaining Device Codes until your device
(e.g. TV) responds to your requested function.
5. Simply repeat the above procedures to enter the Device Codes for your VCR & CBL - (Remember
to press a correct Device Mode Button in step 2 above).
NOTES:
Any Device Codes can be entered into "CBL" & "AUX" modes. (i.e. The "CBL" & "AUX" modes can
be used to control TVs and/or VCRs). Simply press the "CBL" or "AUX" Device Mode Button in step 2
above and enter your 3-digit Device Code for CBL or other devices.
above and enter your 3-digit Device Code for CBL or other devices.
If the indicator flashes twice during the above procedure, a wrong Device Code has been entered. You
are required to repeat steps 2 and 3 again.
If you cannot find a correct Device Code for your equipment, see Setup by SEARCH THROUGH THE
LIBRARY section.
It is highly recommended, for future reference, to write down your Device Codes on the bottom label of
your TEK PARTNER
TM
.
SEARCH THROUGH THE LIBRARY
If you cannot identify a correct Device Code for your equipment from the Device Code List, you may try
the code search method.
the code search method.
For example: Turn on your device (e.g. TV).
1. Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status
indicator lights up.
2. Press a desired Device Mode Button (e.g. "TV").
3. Enter a following corresponding Magic Search Code, and your TEK PARTNER
3. Enter a following corresponding Magic Search Code, and your TEK PARTNER
TM
is now ready to
start searching.
Magic Search Codes:
Magic Search Codes:
TV: 990 VCR: 992 CBL: 994
For example, press... ("PREV CH" & "ENTER" ... "TV" ... 990)
To search: Aim your TEK PARTNER
To search: Aim your TEK PARTNER
TM
at the device (e.g. TV), press the "PWR" and
4. "VOL+" button alternately, repeatedly, slowly and patiently until the device turns off. (NOTE:
There are approximately 70 TV codes, 55 VCR codes, and 55 Cablebox
5. codes.) Once your device has been turned off, immediately press the same Device Mode Button
(e.g. TV) again to lock in the code and the indicator should go out. If the indicator flashes twice
after pressing the "VOL+" Button, you are already at the last code of the library. You may press
"VOL-" to search backward and repeat carefully the above procedures to search again. Simply
repeat the above procedures to search the Device Codes for your VCR and CBL keys. (Remember
to press a correct Device Mode Button in step 2 above).
after pressing the "VOL+" Button, you are already at the last code of the library. You may press
"VOL-" to search backward and repeat carefully the above procedures to search again. Simply
repeat the above procedures to search the Device Codes for your VCR and CBL keys. (Remember
to press a correct Device Mode Button in step 2 above).