Moen 4200 用户手册
Lift Rod & Waste Assembly
(For model with grid strainer assembly follow steps 1-3 only)
1. Thoroughly clean around drain opening in lavatory basin. Apply
1/4 inch bead of plumber's putty (not furnished) around the
underside of seat (as shown).
underside of seat (as shown).
2. Apply pipe joint compound or Teflon tape (not furnished) to top
threaded end of the drain body. Slip drain body up through the
drain opening and screw seat on the drain body.
drain opening and screw seat on the drain body.
3. Position the drain body (with pivot rod opening extending rear-
ward) and tighten mounting nut until the drain body is snug. Wipe
excess plumber's putty from the seat area. Apply pipe joint
compound (not furnished) to top threaded end of tailpipe and
screw into the drain body. Tighten firmly by hand.
excess plumber's putty from the seat area. Apply pipe joint
compound (not furnished) to top threaded end of tailpipe and
screw into the drain body. Tighten firmly by hand.
4. Position the drain plug in either of the following ways:
A. VANDALPROOF - This design is to prevent unauthorized
removal of the drain plug. Unscrew the pivot nut and remove
the pivot rod. Inside the drain body position the pivot rod
through the drain plug hole as shown in the illustration below.
Screw the pivot nut back on the drain body. DO NOT
OVERTIGHTEN.
B. EASY REMOVAL - This design is for quick removal of drain
plug for cleaning. Just drop in the drain plug as shown in the
illustration below.
removal of the drain plug. Unscrew the pivot nut and remove
the pivot rod. Inside the drain body position the pivot rod
through the drain plug hole as shown in the illustration below.
Screw the pivot nut back on the drain body. DO NOT
OVERTIGHTEN.
B. EASY REMOVAL - This design is for quick removal of drain
plug for cleaning. Just drop in the drain plug as shown in the
illustration below.
5. Hook up lift rod and knob, lift rod strap and spring clamp as shown.
6. With the drain plug in full open position, adjust lift rod and knob to
6. With the drain plug in full open position, adjust lift rod and knob to
clear faucet and tighten lift rod strap screw.
DRAIN
PLUG
VANDALPROOF
HOLE
LIFT ROD
AND KNOB
LIFT ROD
STRAP
SCREW
SPRING
CLIP
LIFT ROD
STRAP
PIVOT
ROD
BOTTOM GASKET
FLAT WASHER
PIVOT NUT
PIVOT ROD
SEAT
2-1/8"
1-1/2"
PIPE
JOINT
COMPOUND
OR TEFLON
TAPE
(NOT
FURNISHED)
SEAT
PLUMBERS
PUTTY
MAX 2-1/2"
MIN 1-1/2"
MOUNTING
NUT
DRAIN
BODY
PIPE
JOINT
COMPOUND
(NOT
FURNISHED)
1-1/4"
TAILPIPE
BASIN
8"
FAUCET
CONNECTION
NIPPLE
TIGHTEN
NUT
HOLD WITH
WRENCH
Installation
Be sure lavatory or mounting surface is clean and dry. Place a bead of plumber's putty around the inside lip of the
gasket. Lay gasket on deck and place faucet supplies and studs down through deck holes. Position faucet. Fasten
faucet to deck, using clamp bars, spacers (if necessary), and mounting nuts on studs. Tighten. Engage tailpiece nuts on
supplies to faucet nipples. Tighten nuts.
gasket. Lay gasket on deck and place faucet supplies and studs down through deck holes. Position faucet. Fasten
faucet to deck, using clamp bars, spacers (if necessary), and mounting nuts on studs. Tighten. Engage tailpiece nuts on
supplies to faucet nipples. Tighten nuts.
B. EASY REMOVAL
A. VANDALPROOF
PIVOT
ROD
VANDALPROOF
POSITION
POSITION FOR
EASY REMOVAL
PIVOT
ROD
MT123A
WARNING: Hold the faucet connection nipples with a wrench when
tightening to prevent twisting and collapse of the tubing.
Flushing
IMPORTANT:
Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surface of the
faucet cartridge and cause a leak. To avoid damage, DO NOT OPERATE VALVE until you have followed these instruc-
tions:
faucet cartridge and cause a leak. To avoid damage, DO NOT OPERATE VALVE until you have followed these instruc-
tions:
a. Make sure all water supplies are OFF.
b. Remove handle parts, stop tube, retainer clip and cartridge (see "Disassembly" for detailed instructions).
c. At the supplies, slowly turn both hot and cold water on and thoroughly flush out the body and lines.
b. Remove handle parts, stop tube, retainer clip and cartridge (see "Disassembly" for detailed instructions).
c. At the supplies, slowly turn both hot and cold water on and thoroughly flush out the body and lines.