Moen 4200 用户手册
Disassembly
CAUTION: Turn OFF both hot and cold water supplies. Open handle to alleviate water pressure to insure that
complete water shut-off has been accomplished.
complete water shut-off has been accomplished.
For Knob Models:
1. Remove handle cover, handle screw, knob, stop tube, washer, and retainer clip.
1. Remove handle cover, handle screw, knob, stop tube, washer, and retainer clip.
For Concentrix Handle Models:
1. Remove handle cover, gasket, handle screw, handle insert, handle skirt, handle adapter, stop tube, and retainer clip.
1. Remove handle cover, gasket, handle screw, handle insert, handle skirt, handle adapter, stop tube, and retainer clip.
For Lever Handle Models:
1. Remove handle cap and handle screw. Lift handle assembly up, keeping cartridge stem in down position and tilt up
1. Remove handle cap and handle screw. Lift handle assembly up, keeping cartridge stem in down position and tilt up
and off. Remove clip retainer ring and retainer clip. Slide off grooved sleeve and spacer.
For All Models:
2. Using pliers, grasp the cartridge stem and pull out the cartridge. If cartridge is difficult to remove, turn the cartridge
2. Using pliers, grasp the cartridge stem and pull out the cartridge. If cartridge is difficult to remove, turn the cartridge
shell back and forth with the Moen cartridge wrench (furnished with the new Moen cartridge) or use a Moen cartridge
puller.
puller.
H C
STOP
TUBE
TUBE
KNOB
HANDLE
SCREW
O-RING
HANDLE
COVER
WASHER
HANDLE
SCREW
HANDLE
COVER
STOP
TUBE
TUBE
HANDLE
ADAPTER
SKIRT
HANDLE
INSERT
(NOT INCLUDED)
SPACER
CLIP
RETAINER
RING
GROOVED
SLEEVE
HANDLE
ASSEMBLY
HANDLE
SCREW
HANDLE
COVER
RETAINER
CLIP
CARTRIDGE
GASKET
Reassembly
Fully insert the cartridge until the top of the cartridge ears are level with the top of the faucet body. Position the cartridge
ears up and down to allow insertion of the retainer clip. The notched flat on the stem must point UP when mounting Knob
or Concentrix Handles, DOWN for Lever Handle models. Replace the retainer clip (for lever handles replace spacer,
grooved sleeve, retainer clip, and clip retainer ring) so that the legs straddle the cartridge ears and slide down into the
bottom slot in the body. This prevents the cartridge from rotating and locks it in the body. Reinstall handle parts. Tighten
handle screw securely. Press on handle cover. For Concentrix models install handle insert onto adapter (align locator
notch on handle insert with key on adapter). NOTE: Locator notch on the handle insert must be on the bottom. Fit gasket
up into handle cover recess. Replace handle cover and hand tighten.
ears up and down to allow insertion of the retainer clip. The notched flat on the stem must point UP when mounting Knob
or Concentrix Handles, DOWN for Lever Handle models. Replace the retainer clip (for lever handles replace spacer,
grooved sleeve, retainer clip, and clip retainer ring) so that the legs straddle the cartridge ears and slide down into the
bottom slot in the body. This prevents the cartridge from rotating and locks it in the body. Reinstall handle parts. Tighten
handle screw securely. Press on handle cover. For Concentrix models install handle insert onto adapter (align locator
notch on handle insert with key on adapter). NOTE: Locator notch on the handle insert must be on the bottom. Fit gasket
up into handle cover recess. Replace handle cover and hand tighten.
To Eliminate Cross-Piping on Back-To-Back Installations,
or To Correct Reversed Rough-In Where Hot and Cold Positions Are Reversed
Remove handle parts and stop tube (see "Disassembly"). Turn cartridge stem around so that the notched flat is turned
one half turn or 180
one half turn or 180
°
. Reinstall handle parts. Tighten handle screw securely; replace handle cover.
Cleaning & Care Instructions for
Special Finish Models:
All that is necessary to clean these faucets is to wipe them with a soft, damp cloth such as terrycloth. Warm water will
remove dry water spots. CAUTION: DO NOT use cleansers which contain abrasives or harsh chemicals. NEVER use
alcohol or other organic solvents. A high quality, non abrasive wax polish applied occasionally will help to preserve the
deep tones of the finish.
remove dry water spots. CAUTION: DO NOT use cleansers which contain abrasives or harsh chemicals. NEVER use
alcohol or other organic solvents. A high quality, non abrasive wax polish applied occasionally will help to preserve the
deep tones of the finish.