Husqvarna 324RX 用户手册
ASSEMBLY
English
–
15
CAUTION! Use the recommended blade guard. See the
Technical data section.
Technical data section.
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Place the blade (D) and support flange (F) on the output
shaft.
shaft.
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the
tool kit. Hold the shaft of the spanner as close to the
blade guard as possible. To tighten the nut, turn the
spanner in the opposite direction to the direction of
rotation (Caution! left-hand thread).
35-50 Nm (3.5-5 kpm). Use the socket spanner in the
tool kit. Hold the shaft of the spanner as close to the
blade guard as possible. To tighten the nut, turn the
spanner in the opposite direction to the direction of
rotation (Caution! left-hand thread).
•
When loosening and tightening the saw blade nut, there
is a risk of injury from the teeth of the saw blade. You
should therefore always ensure that your hand is
shielded by the blade guard when doing this. Always use
a socket spanner with a shaft that is long enough to allow
this. The arrow in the diagram shows the area where you
should operate the socket spanner when loosening or
tightening the nut.
is a risk of injury from the teeth of the saw blade. You
should therefore always ensure that your hand is
shielded by the blade guard when doing this. Always use
a socket spanner with a shaft that is long enough to allow
this. The arrow in the diagram shows the area where you
should operate the socket spanner when loosening or
tightening the nut.
Fitting a trimmer guard and
Superauto II 1" trimmer head
Superauto II 1" trimmer head
•
Fit the correct trimmer guard (A) for use with the trimmer
head. Hook the trimmer guard/combination guard onto
the fitting on the shaft and secure with the bolt (L).
head. Hook the trimmer guard/combination guard onto
the fitting on the shaft and secure with the bolt (L).
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
To fit the trimmer head, first separate the two halves (see
diagram). Proceed as follows:
diagram). Proceed as follows:
Insert a finger into the centre hole of the cover (I) while
grasping the cover with your other fingers. Using the
index finger and thumb of your other hand, release the
two catches (J) that engage in the cut-outs in the bottom
half (K). Pull apart the trimmer head, grasping the cover
firmly.
grasping the cover with your other fingers. Using the
index finger and thumb of your other hand, release the
two catches (J) that engage in the cut-outs in the bottom
half (K). Pull apart the trimmer head, grasping the cover
firmly.
•
Place the cover (I) and the support flange (F) on the
output shaft.
output shaft.
•
Fit the nut (G). Tighten the nut to a torque of 35-50 Nm
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible.
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible.
•
To tighten the nut, turn the spanner in the opposite
direction to the direction of rotation (Caution! left-hand
thread).
direction to the direction of rotation (Caution! left-hand
thread).
F
D
B
C
G
G
F
I
A
B
C
K
J
I
K