Husqvarna CTH151 用户手册
6
02601
ASSEMBLY
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Stan dard
wrench sizes are listed.
(2) 7/16" wrenches
wrench sizes are listed.
(2) 7/16" wrenches
Utility knife
(1) 3/4" wrenches
Tire pressure gauge
Pliers
When right or left hand is mentioned in this man ual, it means
when you are in the operating po si tion (seated be hind the
steer ing wheel).
when you are in the operating po si tion (seated be hind the
steer ing wheel).
TO REMOVE TRACTOR FROM
CAR TON
CAR TON
UNPACK CARTON
• Remove all accessible loose parts and parts cartons
from carton.
• Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels fl at.
• Check for any additional loose parts or cartons and
remove.
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
FIG. 1
LOWER
STEERING
SHAFT
STEERING
SHAFT
STEERING
BOOT
BOOT
EXTENSION SHAFT
STEERING
WHEEL
WHEEL
INSERT
ADAPTER
TABS
TAB
SLOTS
SLOTS
BEFORE REMOVING TRACTOR FROM
SKID
SKID
ATTACH STEERING WHEEL (See Fig. 1)
ASSEMBLE EXTENSION SHAFT AND BOOT
• Slide extension shaft onto lower steering shaft. Align
• Slide extension shaft onto lower steering shaft. Align
mount ing holes in extension and lower shafts and install
1/4 hex bolt and lock nut. Tighten securely.
1/4 hex bolt and lock nut. Tighten securely.
IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12
FT. LBS TORQUE.
FT. LBS TORQUE.
• Place tabs of steering boot over tab slots in dash and
push down to secure.
INSTALL STEERING WHEEL
• Position front wheels of the tractor so they are pointing
• Position front wheels of the tractor so they are pointing
straight forward.
• Remove steering wheel adapter from steering wheel
and slide adapter onto steer ing shaft ex ten sion.
• Position steering wheel so cross bars are hor i zon tal
(left to right) and slide inside boot and onto adapt er.
• Assemble large fl at washer, 1/2 hex nut and tighten
se cure ly.
• Snap steering wheel insert into center of steer
ing
wheel.
• Remove protective materials from tractor hood and
grill.
IMPORTANT: CHECK FOR AND RE
MOVE ANY STA
PLES
IN SKID THAT MAY PUNC
TURE TIRES WHERE TRACTOR
IS TO ROLL OFF SKID.
1/4 LOCK NUT
1/4 HEX BOLT
1/2 HEX NUT
LARGE FLAT
WASHER
WASHER
HOW TO SET UP YOUR TRACTOR
CONNECT BATTERY (See Figs. 2)
CAUTION: Do not short battery termi-
nals by allowing a wrench or any other
object to con tact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
nals by allowing a wrench or any other
object to con tact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from accidental
ground ing.
fi rst to prevent sparking from accidental
ground ing.
• If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in the Maintenance section of this
manual for charg ing in struc tions).
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in the Maintenance section of this
manual for charg ing in struc tions).