Husqvarna CTH151 用户手册
7
FIG. 2
025
91
DISCARD TERMINAL
PROTECTIVE CAPS
PROTECTIVE CAPS
BATTERY
COVER
COVER
KEPS
NUT
NUT
HEX BOLT
POSITIVE CABLE
(RED)
(RED)
NEGATIVE
CABLE (BLACK)
CABLE (BLACK)
ASSEMBLY
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob.
• Remove adjustment knob and fl at washer securing
• Remove adjustment knob and fl at washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
of seat to tractor.
• Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
• Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
• Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and fl at washer loosely. Do not tighten.
• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached
• Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down.
way down.
• Get off seat without moving its ad just ed position.
• Raise seat and tighten adjustment knob securely.
• Raise seat and tighten adjustment knob securely.
FIG. 3
TO ROLL TRACTOR OFF SKID (See
Op er a tion section, for location and func tion
of controls)
Op er a tion section, for location and func tion
of controls)
• Press lift lever plunger and raise attachment lift lever
to its highest po si tion.
• Release parking brake by depressing clutch/brake
ped al.
• Place freewheel control in free
wheel ing po
si tion to
dis en gage transmission (See “TO TRANSPORT” in
the Operation section of this manual).
the Operation section of this manual).
• Roll tractor forward off skid.
• Remove banding holding defl ector shield up against
tractor.
TO DRIVE TRAC
TOR OFF SKID (See Op-
er a tion section, for location and func tion of
con trols)
con trols)
WARNING: Before start ing, read, un der stand and follow
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
• Be sure all the above assembly steps have been com-
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
• Be sure all the above assembly steps have been com-
pleted.
• Check engine oil level and fi ll fuel tank with gasoline.
• Place freewheel control in "transmission engaged"
• Place freewheel control in "transmission engaged"
po si tion.
• Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever
• Press lift lever plunger and raise attachment lift lever
to its highest position.
NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
2466
02464
SEAT PAN
SHOUL DER BOLT
AD JUST MENT KNOB
FLAT WASH ER
SEAT
• Remove battery cover.
• Remove terminal protective caps and discard.
• First connect RED battery cable to positive (+) ter-
• Remove terminal protective caps and discard.
• First connect RED battery cable to positive (+) ter-
minal with hex bolt and keps nut as shown. Tighten
securely.
securely.
• Connect BLACK grounding cable to negative (-) ter-
minal with remaining hex bolt and keps nut. Tighten
securely.
securely.
• Replace battery cover.
Open battery cover for:
• Inspection for secure connections (to tighten hard-
• Inspection for secure connections (to tighten hard-
ware).
• Inspection for corrosion.
• Testing battery.
• Jumping (if required).
• Periodic charging .
• Testing battery.
• Jumping (if required).
• Periodic charging .