Roland VS-1824 用户手册
107
Chapter 7 Using Internal Effects (VS8F-2)
Chapter 7
Connecting Loop Effects
The following section explains in detail the steps to connect
loop effects, and provides examples for each method.
loop effects, and provides examples for each method.
1. Select the channel to which the effect is to be added.
Press the SELECT button for either an input channel or a
track channel. The button indicator lights, and the Mixer
Screen appears in the display.
track channel. The button indicator lights, and the Mixer
Screen appears in the display.
2. Use [
], [
], [
], and [
] to move the
cursor to “FX1,” or press [F1 (FX1)]. If “FX1” does not
appear above [F1], press [PAGE] a few times until you
see “FX1”, and then press [F1 (FX1)].
appear above [F1], press [PAGE] a few times until you
see “FX1”, and then press [F1 (FX1)].
fig.05-08
3. Use [
] and [
] to move the cursor. Use the
TIME/VALUE dial to change the values.
Sw (Effect Send Switch)
This selects how the signal is sent to the EFFECT bus.
Off:
Signal is not sent to the EFFECT bus.
Pre:
(Pre-fader). The signal is sent based on its level before
the mixer fader.
the mixer fader.
Pst:
(Post-fader). The signal is sent based on its level after
the mixer fader.
the mixer fader.
Send Level
This adjusts the volume level of the signal (0-127) sent to
the EFFECT bus. The default setting is 100.
the EFFECT bus. The default setting is 100.
Send Pan
This adjusts the stereo placement of the signal (L63-R63)
sent to the EFFECT bus. “L63” is hard left and R63 is
hard right. The default value is “0” (center). This is
useful for isolating channels to the left or right side of a
stereo effect so they can be processed independently.
sent to the EFFECT bus. “L63” is hard left and R63 is
hard right. The default value is “0” (center). This is
useful for isolating channels to the left or right side of a
stereo effect so they can be processed independently.
4. Press [PLAY (DISPLAY)] to return to the Playlist display.
5. Connect FX2-FX4 using the same method.
Effects Return Section
When used in a loop effect, each of the four effects has its
own return level. You can adjust the return level for each
effect using the following procedure.
own return level. You can adjust the return level for each
effect using the following procedure.
* The effect return settings for an individual effect will not
function if that effect is being used as an insert effect.
1. Press the EFFECT 1/3 RTN SELECT button. The Effect
Return screen appears in the display.
2. Press [F3 (FX1)], or use [
], [
], [
], and
[
] to move the cursor to “FX1Rtn.”
3. Use [
] and [
] to move the cursor. Use the
TIME/VALUE dial to change the value.
fig.05-09
Return Level
This sets the volume level (0-127) of the effect. The default
setting is 100.
setting is 100.
Return Balance
This adjusts the stereo placement of the effect (L63-R63) in
the Master Mix. “L63” designates hard left and R63
designates hard right. The default value is 0 (center).
the Master Mix. “L63” designates hard left and R63
designates hard right. The default value is 0 (center).
Effect Send Switch
Effect Send Leve
Effect Send Pan
Return Level
Return Balance
Adjust the Effect Return Level using the
Channel Faders
Channel Faders
1. Press [FADER/MUTE] so “IN” is lit.
2. Use the EFFECT 1 fader to adjust the FX1 return
level.
3. Use the EFFECT 2 fader to adjust the FX2 return
level.
4. Hold [SHIFT] and use the EFFECT 1 fader to adjust
the FX3 return level.
5. Hold [SHIFT] and use the EFFECT 2 fader to adjust
the FX4 return level.
6. After you are finished adjusting the Effect Return
levels, press [FADER/MUTE] so “TR” is lit.