Motorola MVME172 用户手册
3-34
Computer Group Literature Center Web Site
MC2 Chip
3
V10-V8
V10 - V8 are general purpose inputs which are connected
to three jumpers on the MVME172 board. If the bit is set
to a one, the jumper is absent; if it is a zero, the jumper is
present. The jumpers for V10 - V8 are located at J21 pins
5-6, 3-4, 1-2 on the 200/300-Series or J28 pins 11-12, 13-
14, 15-16 on the 400/500-Series (for GPI2, GPI1, and
GPI0, respectively). Refer to your MVME172 installation
and use manual for jumper pin definitions.
to three jumpers on the MVME172 board. If the bit is set
to a one, the jumper is absent; if it is a zero, the jumper is
present. The jumpers for V10 - V8 are located at J21 pins
5-6, 3-4, 1-2 on the 200/300-Series or J28 pins 11-12, 13-
14, 15-16 on the 400/500-Series (for GPI2, GPI1, and
GPI0, respectively). Refer to your MVME172 installation
and use manual for jumper pin definitions.
V11
Refer to the notes following Table 1-3. 200/300-Series
MVME172 Local Bus Memory Map and Table 1-4.
400/500-Series MVME172 Local Bus Memory Map. The
jumper for V11 is located at J21 pins 7-8 on the 200/300-
Series or J28 pins 9-10 on the 400/500-Series (for GPI3).
Refer to your MVME172 installation and use manual for
jumper pin definitions.
MVME172 Local Bus Memory Map and Table 1-4.
400/500-Series MVME172 Local Bus Memory Map. The
jumper for V11 is located at J21 pins 7-8 on the 200/300-
Series or J28 pins 9-10 on the 400/500-Series (for GPI3).
Refer to your MVME172 installation and use manual for
jumper pin definitions.
!
Caution
Removing the jumper from J28, pins 9-10, on the 400/500-
Series module will cause the reset code to execute from
EPROM as described in the MVME172 installation and use
manual.
Series module will cause the reset code to execute from
EPROM as described in the MVME172 installation and use
manual.
V15-V12
V15 - V12 are general purpose inputs. Refer to the
description for V10 - V8. The jumpers for V15 - V12 are
located at J21 pins 15-16, 13-14, 11-12, 9-10 on the
200/300-Series or J28 pins 1-2, 3-4, 5-6, 7-8 (for GPI7,
GPI6, GPI5, and GPI4, respectively). Refer to your
MVME172 installation and use manual for jumper pin
definitions.
description for V10 - V8. The jumpers for V15 - V12 are
located at J21 pins 15-16, 13-14, 11-12, 9-10 on the
200/300-Series or J28 pins 1-2, 3-4, 5-6, 7-8 (for GPI7,
GPI6, GPI5, and GPI4, respectively). Refer to your
MVME172 installation and use manual for jumper pin
definitions.
ADR/SIZ
$FFF4202C (8 bits)
BIT
23
22 - 17
16
NAME
V15
V14 - V9
V8
OPER
R
R
R
RESET
Application Specific