Alcatel Carrier Internetworking Solutions Switch/Router 用户手册
Modifying a PPP Entity
Page 30-15
Modifying a PPP Entity
The
pppmodify
command is used to modify the parameters of an existing PPP Entity. To
modify a specific PPP Entity, for example Peer ID 1, enter the following command:
pppmodify p1
A screen similar to the following displays:
Modify PPP for communication to Peer ID: 1
Enter PPP parameters:
1)
Enter PPP parameters:
1)
Description :
{Enter text up to 30 characters}
{Enter text up to 30 characters}
2)
Administrative Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nable, (D)isable}
{(E)nable, (D)isable}
3)
PPP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal
{(N)ormal, (M)ultilink}
{(N)ormal, (M)ultilink}
4)
Compression Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . None
{(N)one, STAC-(L)ZS}
{(N)one, STAC-(L)ZS}
5)
Bridging Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
{1-65535 or 0 if no Bridging}
50) Bridge Config Admin Status . . . . . . . . . . . . . . . . . . . . . Enabled
{1-65535 or 0 if no Bridging}
50) Bridge Config Admin Status . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nabled, (D)isabled}
51) PPP Bridging Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Only
{Bridge (A)ll, (E)thernet Only}
6)
Routing Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
{1-65535 or 0 if no Routing}
60) IP Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
{1-65535 or 0 if no Routing}
60) IP Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nabled, (D)isabled}
61) Remote IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
{IP address or 0.0.0.0 = learn, if IP enabled}
62) IPX Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . Disabled
{(E)nable, (D)isable}
7)
Authentication Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAP
{(N)one, (P)AP, (C)HAP}
70) User ID received from remote for Authentication . . .
{(N)one, (P)AP, (C)HAP}
70) User ID received from remote for Authentication . . .
{0 (No ID) to 8 ASCII characters}
71) Password received from remote for Authentication .
{0 (No Password) to 8 ASCII characters}
72) User ID sent to remote for Authentication . . . . . . . . .
{0 (No ID) to 8 ASCII characters}
73) Password sent to remote for Authentication . . . . . . .
{0 (No Password) to 8 ASCII characters}
8)
Max Failure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
{1..65535}
{1..65535}
9)
Max Configure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
{1..65535}
{1..65535}
10) Max Terminate Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
{1..65535}
11) Retry Timeout Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
{Retry Timeout in Second(s) 1..65535}
12) Fragmentation Interleaving . . . . . . . . . . . . . . . . . . . . . . . . . No
{Fragmentation Interleaving Yes or No
121) Fragmentation Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 0
121) Fragmentation Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 0
{Fragmentation Delay in milliseconds(ms)}
122) Limit Maximum number of fragmentation to 16 . . . . . No
{(Y) meant cisco compatible. (N) meant native}
:
The fields on this screen are the same as those produced by the
pppadd
command. See
Make the desired changes to any of the parameters, then enter the
save
command to
implement the changes. You will then be returned to the system prompt.