Alcatel Carrier Internetworking Solutions Switch/Router 用户手册
Viewing PPP Entity Configurations
Page 30-17
Routing Group
Indicates the VLAN Group to be used for PPP Routing of the IP and IPX protocols. A value of
zero (
zero (
0
) indicates that this PPP Entity will not perform a routing service and will discard all
routed format packets received or transmitted.
Displaying the Configuration of a Specific PPP Entity
To view configuration information on a specific PPP Entity, you must enter a Peer ID number
with the
with the
pppview
command. For example, to examine Peer ID 1, you would enter the
following command:
pppview p1
A screen similar to the following displays:
View PPP configuration record for communication to Peer ID: 1
1)
1)
Description : Entry Peer ID 1
2)
Administrative Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
3)
PPP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal
4)
Compression Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disabled
5)
Bridging Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
50) Bridge Config Admin Status . . . . . . . . . . . . . . . . . . . . . Enabled
51) PPP Bridging Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Only
50) Bridge Config Admin Status . . . . . . . . . . . . . . . . . . . . . Enabled
51) PPP Bridging Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Only
6)
Routing Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
60) IP Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
61) Remote IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
62) IPX Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . Disabled
60) IP Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
61) Remote IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
62) IPX Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . Disabled
7)
Authentication Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAP
70) User ID received from remote for Authentication . . .
71) Password received from remote for Authentication .
72) User ID sent to remote for Authentication . . . . . . . . .
73) Password sent to remote for Authentication . . . . . . .
70) User ID received from remote for Authentication . . .
71) Password received from remote for Authentication .
72) User ID sent to remote for Authentication . . . . . . . . .
73) Password sent to remote for Authentication . . . . . . .
8)
Max Failure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
9)
Max Configure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10) Max Terminate Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
11) Retry Timeout Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12) Fragmentation Interleaving . . . . . . . . . . . . . . . . . . . . . . . . . No
11) Retry Timeout Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12) Fragmentation Interleaving . . . . . . . . . . . . . . . . . . . . . . . . . No
{Fragmentation Interleaving Yes or No
121) Fragmentation Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 0
121) Fragmentation Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 0
{Fragmentation Delay in milliseconds(ms)}
122) Limit Maximum number of fragmentation to 16 . . . . . No
{(Y) meant cisco compatible. (N) meant native}
The fields on this screen are similar to those produced by the
pppadd
command. A few
differences are noted in the descriptions that are given below. Note that you cannot make
changes to the parameters on this screen. To do so, you must use the
changes to the parameters on this screen. To do so, you must use the
pppmodify
command