Korg triton-rack 信息指南

The insert effects, master effects, and master EQ have 
the same structure in all modes, but the routing set-
tings will determine how the oscillators of a program 
or the timbres of a combination or track of a song will 
be sent to each insert effect or master effect. In the 
pages that follow, we will explain how you can make 
routing settings and effect settings in each mode.

1 Select the PROG 7.1: Ed-BUS, BUS page.

2 Use “BUS Select (All OSCs)” to specify the bus 

 The output will not be sent to the insert effects. 

After passing through the master EQ, the sound will 
be sent to AUDIO OUTPUT (MAIN) L/MONO and 
R.
IFX1–5:

 The output will be sent to insert effect IFX 1, 

2, 3, 4, or 5.
1, 2, 3, 4, 1/2, 3/4: 

The output will be sent to AUDIO 

OUTPUT (INDIVIDUAL) 1, 2, 3, or 4. It will not be 
sent to the insert effects, the master effects, or the 
master EQ.
Off: 

The output will not be sent to AUDIO OUTPUT 

(MAIN) L/MONO, R, or to (INDIVIDUAL) 1, 2, 3, 4. 
(After passing through the master effects, it will be 
output from AUDIO OUTPUT (MAIN).) Select this 
when you wish to connect the output to the master 
effects in a series connection at the send levels speci-
fied by “MFX Send.”

The Routing page displays the state of the routing, 
insert effect, and chain settings. In this page you 
can also set “BUS Select.” Use the [INC]/[DEC] 
keys to select the send destination to the insert 
effects.

3 “MFX Send” specifies the send level from each 

This is valid only if “BUS Select (All OSCs)” is set to 
L/R

 or Off.

If IFX1–5 is selected for “BUS Select (All OSCs),” the 
send level to the master effects is adjusted by the 
“Send 1 (MFX1)” and “Send 2 (MFX2)” parameters 

(PROG 7.2: Ed-Insert FX, Setup page) after the sig-
nal has passed through the insert effects.

4 Select the PROG 7.2: Ed-InsertFX, Setup page.

5 For “Insert Effect 1”–“Insert Effect 5,” select the 

The “Select by Category” utility lets you select 
effects from six categories.

Double-size effects 090–102 can be used only for 
IFX 2, 3, or 4.

6 Use “On/Off” to switch each insert effect on/off.

A setting of Off will be the same state as when 000: 
No Effect is selected. The input sound will be output 
without change.

The “Copy Insert Effect” utility lets you copy effect 
settings from another program etc. The “Swap 
Insert Effect” utility lets you exchange the settings 
of two insert effects, such as IFX1 and IFX5.

7 Specify the “Chain” setting.

If you set “Chain” to 

, insert effects will be con-

nected in series. If you send the oscillator output to 
IFX1 as shown in the illustration for step 1 and 
make settings as shown in illustration 4, the signal 
will be sent in series through the five insert effects 
IFX1

→

IFX2

→

IFX3

→

IFX4

→

IFX5, and will finally be 

output.

8 Make settings for “Pan(CC#8),”“BUS Select,” “S1 

If the insertion effects are chained, these settings will 
apply after the last IFX.
“Pan(CC#8)”: 

Set the pan. This is valid only when 

“BUS Select” is L/R.
“BUS Select”: 

Specify the output destination. Nor-

mally you will set this to L/R. If you wish to send 
the sound that has passed through the insert effects 
to AUDIO OUTPUT (INDIVIDUAL) 1–4, select 1–4, 
1/2

, or 3/4.

 Set the 

send levels to the master effects. For this example, 
set this to 127.

9 Select the IFX1–IFX5 pages, and set the parameters 

For details on the parameters of each effect (

☞