JVC KENWOOD Corporation 407110 用户手册

25

Usually you can communicate with other stations 
using a single frequency for receiving and transmitting.  
In this case, you select only one frequency on either 
VFO A or VFO B.  However, there are cases where 
you must select one frequency for receiving and a 
different frequency for transmitting.  This requires the 
use of 2 VFOs.  This is referred to as “split-frequency 
operation”.  One typical case which requires this type 
of operation is when you use  an FM repeater {page 

26}

.  Another typical case is when you call a rare DX 

station.

When a rare or desirable DX station is heard, that 
operator may immediately get many simultaneous 
responses.  Often, such a station is lost under the noise 
and confusion of many calling stations.  If you find that 
you are suddenly being called by many operators, it 
is your responsibility to control the situation.  You may 
announce that you will be “listening up 5 (kHz, from 
your present transmission frequency)”, or “listening 
down between 5 and 10 (kHz)”.

1 Press 

[A/B (A=B)] to select VFO A or VFO B.

s

” or “

” appears to show which VFO is 

selected.

2  Select an operating frequency.

s

other VFO, press and hold [A/B (A=B)].

3 Press 

[A/B (A=B)] to select the other VFO.

4  Select an operating frequency.

s

5 Press 

[SPLIT].

s

” appears.

s

and transmission frequencies are swapped.

6  To quit split-frequency operation, press [SPLIT] 

again.

s

” disappears.

When the shiftable function of the RX frequency 
in split transmission is set to ON, it is possible to 
change the RX frequency by turning the Tuning control 
during split transmission. (When it is set to OFF, the 
TX frequency changes by turning the Tuning control 
during split transmission.)

1 Press 

[MENU], then press [Q-M.IN]/ [Q-MR] or 

turn the MULTI/CH control to select Menu No. 20.

2 Press 

[M.IN]/ [SCAN (SG.SEL)] to select “on” 

3 Press 

[MENU] to exit Menu mode.

s

function is set to ON, the decimal point at the 

right end digit of the main display flashes for 
approximately 2 seconds after the Power On 
message is displayed.

To directly enter the difference between the TX 
and RX frequencies specified by a DXer, follow the 
instruction below while receiving on the main band of 
a signal from the DXer.

1  Press and hold [SPLIT].

s

” blinks.

order of kHz as specified by the DX station.

If the frequency specified by the DXer is higher 

than your current frequency, enter the specified 
frequency in the order of kHz using the numeric 
and band-select keypad. Conversely, if the 
specified frequency is lower, prefix a value of 
"0" to the frequency.

s

the frequency by 5 kHz, and enter a value of 
"05" to decrement the frequency by 5 kHz.

s

” switches from split operation to simplex 

operation.

◆

 Pressing 

[SPLIT] switches from split operation to simplex 

operation.

◆

  To temporarily receive using the transmit frequency, use the 

4& 3%4

To directly search for the transmit frequency by 
rotating the Tuning control, follow the instruction 
below while receiving on the main band of a signal 
from the DX station.

1  Press and hold [SPLIT].

s

” blinks.

2  Turn the Tuning control to search for the frequency.

s

frequency has been locked.

s

3 Press 

[SPLIT] to end.

s

frequency and split operation begins.

s

” lights.