Bosch Appliances Home Security System DS7400XIV4-EXP 用户手册
DS7400XiV4-EXP | User Guide | 6.0 Day to Day Operations
EN | 13
Bosch Security Systems | 6/05 | 4998154961B
6.2 Optional
Operations
6.2.1 Quick
Arming
Quick arming allows you to enter some arming commands without first entering a PIN. If quick arming is
not
used, you must enter a PIN at the beginning of all arming command sequences.
Quick arming is not available from a Master keypad or from RF (wireless) keypads.
The following shortcuts are allowed when the system is programmed for quick arming:
Table 9: Quick Arming
Type of Arming
Quick Arming Command Sequence
Normal Arming
[#][On]
Perimeter Instant Arming – no entry delay
[#][No Entry][Perimeter Only]
Perimeter Arming – entry/exit delay in effect
[#][Perimeter Only]
Maximum Security Arming
[#][No Entry][On]
6.2.2 Force
Arming
When one or more zones are faulted (for example, if a window or door is open), the system can be force armed (if
programmed) by bypassing the faulted zones. When a text keypad displays “Not Ready” and the zone LED(s) on
an LED keypad for the faulted zone(s) are lit, force arming is required to arm the system. Although an RF3341
keypad does not indicate a faulted state on the system, you can force arm the system from an RF3341 keypad.
You can also force arm an area using a master keypad in Single Partition Mode.
programmed) by bypassing the faulted zones. When a text keypad displays “Not Ready” and the zone LED(s) on
an LED keypad for the faulted zone(s) are lit, force arming is required to arm the system. Although an RF3341
keypad does not indicate a faulted state on the system, you can force arm the system from an RF3341 keypad.
You can also force arm an area using a master keypad in Single Partition Mode.
Force Arming during an AC power failure: Regular arming of the control panel is not permitted during an
AC power failure. The requirement to force arm serves as a warning that the control panel is operating under
backup battery.
AC power failure. The requirement to force arm serves as a warning that the control panel is operating under
backup battery.
Bypassing or force arming removes some of your building’s protection because it excludes the faulted
zones from arming. Therefore, an intrusion might not be detected or the detection might be delayed.
Always attempt to correct any zone problems (close doors and windows, etc.) before using these
features. If you cannot correct the problem, contact your installing company.
zones from arming. Therefore, an intrusion might not be detected or the detection might be delayed.
Always attempt to correct any zone problems (close doors and windows, etc.) before using these
features. If you cannot correct the problem, contact your installing company.
Table 10: Force Arming
Equipment
Command Sequence
What Happens
What To Do
Text Keypad LED
Keypad
Keypad
Enter any Arming
Command Sequence.
Enter [Bypass] during the
five-second beep.
Command Sequence.
Enter [Bypass] during the
five-second beep.
• The red Armed LED flashes during the
exit-delay period.
• All zones normally armed by the
Arming Command Sequence are
armed except for the faulted zones.
armed except for the faulted zones.
If leaving, exit during the exit-
delay period.
delay period.
RF3341 Keypad
Any Arming Command
Sequence [9]
Sequence [9]
• The LED flashes indicating a signal
was sent to your security system.
• All zones normally armed by the
Arming Command Sequence are
armed except for the faulted zones.
armed except for the faulted zones.
If leaving, exit during the exit-
delay period.
delay period.
RF3332/RF3332E,
RF3334/RF3334E
RF3334/RF3334E
Not applicable
* Text Keypad only