Windsor SC20 Benutzerhandbuch

SABER (SC)   86038350   01/29/07 

 

1.  Choose a smooth, level surface.  Turn “ON” the 

key switch and vacuum switch.  Lower the 
squeegee and drive forward at least 2 feet 
(60cm.). 

2.  With the squeegee down, stop the machine.  Do 

not allow machine to roll back. 

 
FOR SAFETY:  Before leaving or servicing the 
machine, stop on level surface, turn off machine 
and remove key. 
 
3.  Determine the differences, if any, in deflection of 

the squeegee blade between each end and the 
middle.  Proper adjustment is obtained when 
deflection is equal all the way across the 
squeegee blade.   

4.  To decrease the deflection of the squeegee 

blade at the ends, adjust plastic knobs at the far 
right or left of squeegee assembly. 

5.  Check the deflection of the squeegee blades 

again.  Repeat steps 1 through 4 until the 
deflection is equal across the entire rear 
squeegee blade. 

 

   

 
1.  Choose a smooth, level surface.  Turn “ON” the 

key switch and vacuum switch.  Lower the 
squeegee and drive forward at least 2 feet 
(60cm.). 

2.  With the squeegee down, stop the machine.  Do 

not allow machine to roll back. 

 
FOR SAFETY:  Before leaving or servicing 
machine, stop on level surface, turn off machine 
and remove key. 
 
3.  Observe the amount of squeegee deflection.  It 

should deflect approximately 3/8 in. (9.5mm) 
across the entire width of the squeegee. 

4.  To increase the squeegee deflection, turn the 

center knob above the lift carrier bracket 
clockwise.  To decrease the deflection, turn the 
knob counterclockwise.  

 
NOTE: The deflection should be consistent along 
the length of the squeegee.  If the deflection varies 
from end to end the knobs can be adjusted 
independently to correct the variation. 
 
5.  Turn on the key switch.  Raise, then lower 

squeegee assembly.  Drive forward at least 2 
feet (60cm). 

6.  Repeat steps 2 through 4 until deflection of 

approximately 3/8 in. (9.5mm) is reached. 

 

 
1.  With the squeegee in the up position, turn key 

switch “OFF”. 

 
FOR SAFETY: Before leaving or servicing 
machine; stop on level surface, turn off machine 
and remove key. 
 
2.  Remove the squeegee assembly from the 

machine.  Unlatch and remove blade retainer 
strap and remove squeegee blade. 

3.  Rotate the squeegee to new edge position or 

replace as required.  Each blade has four edge 
positions. 

4.  Install blade on locating tabs of squeegee 

assembly. 

5.  Install squeegee retainer strap. 
6.  Fasten and lock latch, adjust latch only tight 

enough to take up slack in retaining strap. 

 

1.  With the squeegee in the up position, turn key 

switch “OFF”. 

2.  Remove the squeegee from the machine. 

Loosen (3) thumb screws securing retainer 
strap. 

3.  Remove front retainer strap. 
4.  Remove squeegees blade from locating tabs on 

squeegee assembly and rotate to new position 
or replace as required. 

5.  Install blade on locating tabs of squeegee tool. 
6.  Replace front retainer strap. 
7.  Secure strap by tighten (3) thumb screws. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
1.  Apply 1-2 strokes of MOBILTEMP

®78 or  

compatible clay-based or calcium-based grease  
per service schedule.