ATTO Technology 1550D Benutzerhandbuch
vii
ATTO Technology Inc. iPBridge Installation and Operation Manual
Date
Regulates the current date for this iPBridge. The date
range is 1/1/2000 to 12/31/2099.
Regulates the current date for this iPBridge. The date
range is 1/1/2000 to 12/31/2099.
set Date [MM] / [DD] / [YYYY]
get Date
get Date
DeleteAllMaps
Removes all mapped devices from the map table. Upon
the subsequent POST, the default maps are loaded if no
maps are present.
Removes all mapped devices from the map table. Upon
the subsequent POST, the default maps are loaded if no
maps are present.
DeleteAllMaps
SaveConfiguration command required
SaveConfiguration command required
DPMTU
Controls the MTU, or maximum transmission unit, used
by the data port.
Controls the MTU, or maximum transmission unit, used
by the data port.
default: 1514
set DPMTU [dp1 | all] [1514 | 9014]
get DPMTU [dp1 | all]
set DPMTU [dp1 | all] [1514 | 9014]
get DPMTU [dp1 | all]
DumpConfiguration
Displays the iPBridge configuration to the ExpressNlAV
Advanced page text box, an available RS-232 or telnet
session.Results may be truncated in the ExpressNAV
readout.
Displays the iPBridge configuration to the ExpressNlAV
Advanced page text box, an available RS-232 or telnet
session.Results may be truncated in the ExpressNAV
readout.
DumpConfiguration
DumpEventLog
Dumps the entire contents of the event log to the
ExpressNlAV Advanced page text box, an available RS-
232 or telnet session.Results may be truncated in the
ExpressNAV readout.
Dumps the entire contents of the event log to the
ExpressNlAV Advanced page text box, an available RS-
232 or telnet session.Results may be truncated in the
ExpressNAV readout.
DumpEventLog
EthernetSpeed
Regulates the speed of the iPBridge Ethernet port. If
Auto is enabled, the Ethernet speed is negotiated. When
hard set, 10 and 100 speeds are half duplex.
Regulates the speed of the iPBridge Ethernet port. If
Auto is enabled, the Ethernet speed is negotiated. When
hard set, 10 and 100 speeds are half duplex.
Default: auto
set EthernetSpeed [dp1 | all] [10 | 100 | 1000 | auto]
get EthernetSpeed [dp1 | all]
set EthernetSpeed [dp1 | all] [10 | 100 | 1000 | auto]
get EthernetSpeed [dp1 | all]
Exit
Terminates the current CLI session over Telnet. This
command has no effect if used during a serial CLI
session.
Terminates the current CLI session over Telnet. This
command has no effect if used during a serial CLI
session.
Exit
FirmwareRestart
Resets and reinitializes the iPBridge firmware. Use the
forced option to override any CLI reservations held by
other sessions.
Resets and reinitializes the iPBridge firmware. Use the
forced option to override any CLI reservations held by
other sessions.
FirmwareRestart <forced>
Help
Issued with no parameters displays a list of available CLI
commands. When a CLI command name is specified, a
command usage string and command description are
displayed.
Issued with no parameters displays a list of available CLI
commands. When a CLI command name is specified, a
command usage string and command description are
displayed.
Help <Command>
IdentifyBridge
Causes both the Activity and SCSI LEDs on the
iPBridge to blink so that you can identify the iPBridge
hardware. Disabling this option cancels the blinking.
Causes both the Activity and SCSI LEDs on the
iPBridge to blink so that you can identify the iPBridge
hardware. Disabling this option cancels the blinking.
Default: disabled
set IdentifyBridge [enabled | disabled]
get IdentifyBridge
set IdentifyBridge [enabled | disabled]
get IdentifyBridge
Info
Displays version numbers and other product information
for key components within the iPBridge.
Displays version numbers and other product information
for key components within the iPBridge.
Info
is enabled, the get command
reports the current IP address assigned by the network
DHCP server, followed by the (DHCP) identifier.
DHCP server, followed by the (DHCP) identifier.
Default: 10.0.0.0 if IPDHCP is disabled
set IPAddress [dp1] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPAddress [dp1 | all]
set IPAddress [dp1] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPAddress [dp1 | all]
IPDHCP
Regulates how the iPBridge acquires its IP address.
When disabled, the iPBridge uses the IP address
specified by the
Regulates how the iPBridge acquires its IP address.
When disabled, the iPBridge uses the IP address
specified by the
CLI command.; when
enabled, the iPBridge gets its IP address from a DHCP
server.
server.
Default: enabled
set IPDHCP [dp1 | all] [enabled | disabled]
SaveConfiguration Restart command required
get IPDHCP [dp1 | all]
set IPDHCP [dp1 | all] [enabled | disabled]
SaveConfiguration Restart command required
get IPDHCP [dp1 | all]