Vacmaster Vacuum Cleaner VHB307WM Benutzerhandbuch
8
LIQUID VACUUMING
WARNING:
BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY
INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
WARNING
:
DO
NOT PLUG IN POWER CORD TO POWER OUTLET
.
MAKE SURE PLUG IS
DISCONNECTED BEFORE CHANGING THE FILTERS.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Remove reusable cloth filter, then carefully install the foam sleeve filter over the filter cage and place the
power head back on the collection tank. (fig. 2, 3 & 4) See filter installing instructions on page 10.
DO NOT USE THE REUSABLE CLOTH FILTER FOR LIQUID VACUUMING.
DO NOT USE COLLECTION BAG FOR LIQUID VACUUMING.
DO NOT USE COLLECTION BAG FOR LIQUID VACUUMING.
OPERATING INSTRUCTIONS – WET VACUUMING
3. Fit the desired nozzle to the vacuum hose. (fig. 5)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig. 6)
5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.7)
6. After use, empty the collection tank, clean and dry the inside and outside before storage.
3. Fit the desired nozzle to the vacuum hose. (fig. 5)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig. 6)
5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.7)
6. After use, empty the collection tank, clean and dry the inside and outside before storage.
IMPORTANT!
When vacuuming large quantities of liquids, do not immerse the nozzle completely in the
liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve
that stops the suction action when the collection tank reaches its maximum capacity. You will notice an
increase in motor speed. When this happens, turn off the machine, disconnect from power supply, and
drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the power head to the
collection tank. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the
collection tank, clean and dry the inside and outside before storage.
that stops the suction action when the collection tank reaches its maximum capacity. You will notice an
increase in motor speed. When this happens, turn off the machine, disconnect from power supply, and
drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the power head to the
collection tank. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the
collection tank, clean and dry the inside and outside before storage.
REMEMBER!
The foam filter must be removed after wet vacuuming, and a reusable cloth filter must be
installed before dry vacuuming again.
LIQUID VACUUM OPERATION