Leibherr USA Refrigerators and freezers for integrated use, door-on-door HRB 1110 HF 851 Benutzerhandbuch
u
Remove the protective film from the
trim
Fig. 19 (20)
.
u
Place the trim
Fig. 19 (20)
on the flange of
the cover
Fig. 18 (16)
, on the handle side
and flush with the front, and adhesively
affix it to the side wall of the appliance.
u
If necessary, shorten the trim
Fig. 19 (20)
at the bottom: The trim
Fig. 19 (20)
must end 1/8 '' (3 mm) above
the upper edge of the bottom mounting
bracket
Fig. 11 (17)
.
Fig. 19
Insert and align appliance:
u
Slide the appliance in until it contacts
Fig. 18 (16)
the
covers
Fig. 18
on the side wall of the unit.
With 5/8 '' (16 mm) thick unit
walls:
u
Slide the appliance into the
recess until it touches the
spacers on the side wall of the
unit.
Fig. 20
With 3/4 '' (19 mm) thick
unit walls:
u
Align the front edges of the
hinges flush with the side wall
of the unit.
Fig. 21
Units (5/8 '' (16 mm) and 3/4 '' (19 mm)) with door
stop components (knobs, sealing lips, etc.):
u
Note the additional space needed (for depth of door stop
components): Allow the hinges and covers
Fig. 18 (16)
to
protrude by the additional distance.
All appliances:
u
Adjust the adjustable feet with the supplied open-ended
wrench
Fig. 11 (21)
to align the appliance vertically.
w
The appliance is now positioned correctly depthwise.
The distance between the front edge of the unit side wall
and the appliance itself is 42 mm all around. (Note the
additional space needed for door stop components such
as knobs and sealing lips.)
Note
Malfunction due to incorrect assembly!
If the spacing is not observed, the appliance door may not
seal completely. This can cause icing up, the formation of
condensate, and malfunctions.
u
A continuous space of 1-21/32 '' (42 mm) must be
maintained. (Note the additional space needed for door
stop components such as knobs and sealing lips.)
To secure the appliance in the recess:
u
Screw long chipboard screws
Fig. 22 (22)
at the top and at the
bottom through the hinge plates.
Take care that screws will not
protrude from an exposed end
cabinet wall.
Fig. 22
On the top handle side:
u
Loosen the screws
Fig. 23 (19)
slightly.
u
Secure the top mounting
bracket
Fig. 23 (17)
with a
ø4x19 chipboard screw
Fig. 23 (25)
to the unit
wall.
u
Break off the protruding
end of the cover
Fig. 23 (16)
.
Fig. 23
u
Tighten the screws
Fig. 23 (19)
.
u
Place cover
Fig. 23 (16)
in position.
On the bottom handle side:
u
Loosen
the
screws
Fig. 24 (19)
slightly.
u
Secure
the
bottom
mounting
bracket
Fig. 24 (17)
with a ø4x19
chipboard
screw
Fig. 24 (25)
to the unit wall.
u
Break off the protruding
end
of
the
cover
Fig. 24 (16)
.
u
Tighten
the
screws
Fig. 24 (19)
.
u
Place
the
cover
Fig. 24 (23)
onto the
bottom mounting bracket
Fig. 24 (17)
.
Fig. 24
u
Slide the equalizer trim
Fig. 15 (11)
toward the handle side
as far as it will go.
u
Close the appliance door.
6.2 Fitting the unit doors
Fig. 25
Installation
11