Thermador PRG366JG Installationsanweisungen
English 2
Important Installation Information
Gas Type Verification
Verify the type of gas supplied to the location. Ensure that
the appliance is connected to the type of gas for which it is
certified. All ranges are certified for use with natural gas or
propane (LP) gas. Make certain the range matches the gas
type available.
the appliance is connected to the type of gas for which it is
certified. All ranges are certified for use with natural gas or
propane (LP) gas. Make certain the range matches the gas
type available.
Refer to “Step 6: Gas Requirements and
Hookup” on page 14 before proceeding with the installation.
Gas Supply:
Natural Gas — 6 inch water column. (14.9 mb) min., 14
inch (34.9 mb) maximum
inch (34.9 mb) maximum
Propane Gas — 11 inch water column. (27.4 mb) min., 14
inch (34.9 mb) maximum
inch (34.9 mb) maximum
Electric Power Supply:
36" Models:
6 Burners – 120 VAC, 60 Hz., 1Ph., 15 Amp circuit
4 Burners with Griddle – 120 VAC, 60 Hz., 1Ph., 20 Amp
circuit
6 Burners – 120 VAC, 60 Hz., 1Ph., 15 Amp circuit
4 Burners with Griddle – 120 VAC, 60 Hz., 1Ph., 20 Amp
circuit
48" Models:
6 Burners with Griddle – 120 VAC, 60 Hz., 1Ph., 20 Amp
circuit
6 Burners with Griddle – 120 VAC, 60 Hz., 1Ph., 20 Amp
circuit
Check local building codes for the proper method of
appliance installation. Local codes vary and it is the
responsibility of the installer to ensure installation is in
accordance with these codes. Installation, electrical
connections and grounding must comply with all applicable
codes. In the absence of local codes the appliance should
be installed in accordance with the National Fuel Gas Code
ANSI Z223.1/ NFPA 54 current issue and National
Electrical Code ANSI/NFPA 70 -current issue. In Canada,
installation must be in accordance with the CAN 1-B149.1
and .2 – Installation Codes for Gas Burning Appliances
and/or local codes.
appliance installation. Local codes vary and it is the
responsibility of the installer to ensure installation is in
accordance with these codes. Installation, electrical
connections and grounding must comply with all applicable
codes. In the absence of local codes the appliance should
be installed in accordance with the National Fuel Gas Code
ANSI Z223.1/ NFPA 54 current issue and National
Electrical Code ANSI/NFPA 70 -current issue. In Canada,
installation must be in accordance with the CAN 1-B149.1
and .2 – Installation Codes for Gas Burning Appliances
and/or local codes.
IMPORTANT:
When installing against a combustible surface, a High Shelf
or Low Backguard is required. A THERMADOR
or Low Backguard is required. A THERMADOR
®
High
Shelf or Low Backguard must be purchased separately.
See Step 8 on page 16 for backguard, kits and installation
information.
See Step 8 on page 16 for backguard, kits and installation
information.
When using the Flush Island Trim, THERMADOR
recommends a minimum 12” (305 mm) rear clearance to a
combustible surface (see Figure 1, Cabinet Clearances).
Clearances from non-combustible materials are not part of
the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be
approved by the local codes and/or by the local authority
having jurisdiction.
recommends a minimum 12” (305 mm) rear clearance to a
combustible surface (see Figure 1, Cabinet Clearances).
Clearances from non-combustible materials are not part of
the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be
approved by the local codes and/or by the local authority
having jurisdiction.
Refer to “Backguard Kit Model Numbers” on page 21, for
the correct backguard models that are designed for this
range. After selecting the correct backguard, the range
must be installed properly, using the minimum clearances
to combustible surfaces specified in See “Step 2: Cabinet
Preparation” on page 4.
the correct backguard models that are designed for this
range. After selecting the correct backguard, the range
must be installed properly, using the minimum clearances
to combustible surfaces specified in See “Step 2: Cabinet
Preparation” on page 4.
WARNING:
To avoid possible burn or fire hazard, a backguard
designed specifically for this range must be installed
whenever the range is used.
designed specifically for this range must be installed
whenever the range is used.
CAUTION:
When connecting the unit to propane gas, make certain
the propane gas tank is equipped with its own high-
pressure regulator in addition to the pressure regulator
supplied with the range. The maximum gas pressure to
this appliance must not exceed 14.0” water column (34.9
mb) from the propane gas tank to the pressure regulator.
the propane gas tank is equipped with its own high-
pressure regulator in addition to the pressure regulator
supplied with the range. The maximum gas pressure to
this appliance must not exceed 14.0” water column (34.9
mb) from the propane gas tank to the pressure regulator.
CAUTION:
This unit is designed as a cooking appliance. Based on
safety considerations, never use it for warming or
heating a room.
safety considerations, never use it for warming or
heating a room.
CAUTION:
To eliminate risk of burns or fire caused by reaching over
heated surface units, cabinet storage located above the
surface units should be avoided.
heated surface units, cabinet storage located above the
surface units should be avoided.