Avaya 03-300430 User Manual
Communication Manager Maintenance-Object Repair Procedures
700 Maintenance Procedures for Avaya Communication Manager 3.0, Media Gateways and Servers
The Activated state is the correct state for an ISDN-BRI port. In this state the Level 1 interface
can communicate with the BRI endpoint or ASAI or Avaya adjunct administered on this port.
This test passes if the state of Level 1 (L1) is Activated. This test also passes if software has
taken this port out of service. See the description of the Level 1 “Deactivated State” below for
more details.
The Pending Activation state indicates a problem with the endpoints or adjunct, the wiring to the
sets or adjunct, or the BRI-LINE circuit pack. When in this state, the Level 1 interface is either
not receiving any L1 framing from the endpoint or adjunct (Endpoint Idle), or it is communicating
with the endpoint or adjunct but cannot transition to the Activated state (Endpoint Active).
The Deactivated state indicates a problem with the BRI-LINE circuit pack. When in this state,
the Level 1 interface is idle and is not trying to communicate with the BRI endpoints or adjunct.
When an ISDN-BRI port is placed in the out-of-service state, Level 1 is also put into the
Deactivated state. This could be due either to the system detecting a fault with the port or to a
busyout port location request.
can communicate with the BRI endpoint or ASAI or Avaya adjunct administered on this port.
This test passes if the state of Level 1 (L1) is Activated. This test also passes if software has
taken this port out of service. See the description of the Level 1 “Deactivated State” below for
more details.
The Pending Activation state indicates a problem with the endpoints or adjunct, the wiring to the
sets or adjunct, or the BRI-LINE circuit pack. When in this state, the Level 1 interface is either
not receiving any L1 framing from the endpoint or adjunct (Endpoint Idle), or it is communicating
with the endpoint or adjunct but cannot transition to the Activated state (Endpoint Active).
The Deactivated state indicates a problem with the BRI-LINE circuit pack. When in this state,
the Level 1 interface is idle and is not trying to communicate with the BRI endpoints or adjunct.
When an ISDN-BRI port is placed in the out-of-service state, Level 1 is also put into the
Deactivated state. This could be due either to the system detecting a fault with the port or to a
busyout port location request.
Table 235: Test #621 Level 1 Status Inquiry
Error
Code
Code
Test
Result
Result
Description / Recommendation
1187
ABRT
The board, port or station may have been busied out by a technician.
1. Look in the Error Log for Error Type 18 (port busied out) for this port
and BRI-BD (board busied out). If this error type is present for
BRI-PORT only, release the port via release port pp and run the
BRI-PORT only, release the port via release port pp and run the
test again. If the error is present for both BRI-BD and BRI-PORT, then
release the board via release port location and run the test
release the board via release port location and run the test
again.
Note:
Note:
When you release a port, you release every port associated
with it. If certain ports still need to be busied out, use port
location to busy them out.
with it. If certain ports still need to be busied out, use port
location to busy them out.
2. Make sure the terminal is connected.
3. Retry the command at 1-minute intervals up to 5 times.
4. If the test continues to abort, escalate the problem.
2000
ABRT
Response to the test was not received from the circuit pack within the
allowable time period.
allowable time period.
1. If the test aborts repeatedly up to five times, reset the circuit pack via
the busyout board location and reset board location.
2. If the test aborts again, replace the circuit pack.
1 of 4