Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 15.0
System Reporting Information
EN | 67
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
An RF Receiver Trouble Report (Contact ID Event
Code 355) is sent to the base station receiver when
the RF receiver registers one of these events:
Code 355) is sent to the base station receiver when
the RF receiver registers one of these events:
RF Signal Jamming (Point ID Code 001)
RF Receiver Tamper Switch (Point ID Code 002)
RF Receiver Failure (Point ID Code 003)
RF Receiver Tamper Switch (Point ID Code 002)
RF Receiver Failure (Point ID Code 003)
15.11 RF Receiver Trouble Restore
Report
Location
398 to 399
Location
Default
Tens digit
398
7
Units digit
399 11
An RF Receiver Trouble Restore Report is sent to
the base station receiver when the RF receiver no
longer registers RF Signal Jamming, RF Receiver
Tamper Switch, or RF Receiver Failure.
the base station receiver when the RF receiver no
longer registers RF Signal Jamming, RF Receiver
Tamper Switch, or RF Receiver Failure.
15.12 RF Dialer Options
Location
400
0
No report allowed
1
Report to Receiver 1
2
Report to Receiver 2
4
Report to both Receiver 1 and Receiver 2
8
Report to Receiver 2 only if Receiver 1 fails
Location 400 is set by default to report only to
Receiver 1. You can select whether Zone Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or there is no
reporting at all.
Receiver 1. You can select whether Zone Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or there is no
reporting at all.
15.13 Open/Close Reports
Location
401 to 402
Location
Default
Open Report
401
11
Close Report
402 12
An Opening Report (Contact ID Event Code 401) is
sent to the base station receiver when the system is
disarmed from AWAY Mode. A Closing Report
(Contact ID Event Code 401) is sent at the end of
Exit Time when the system is armed in AWAY
Mode.
sent to the base station receiver when the system is
disarmed from AWAY Mode. A Closing Report
(Contact ID Event Code 401) is sent at the end of
Exit Time when the system is armed in AWAY
Mode.
If an expanded format is selected, this code is used as
the Expansion Code and the user number that armed
or disarmed the system follows in the same
transmission.
the Expansion Code and the user number that armed
or disarmed the system follows in the same
transmission.
To enable Open and Close Reports in STAY
Mode:
Mode:
Select Option 2 in Location 178 (refer to Section 12.2
Dialer Options 2 on page 53). To enable Open and
Close Reports only after a previous alarm, select
Option 1 in Location 178.
Dialer Options 2 on page 53). To enable Open and
Close Reports only after a previous alarm, select
Option 1 in Location 178.
If Open and Close Reports are not
required, program Locations 401 and 402
as 0.
required, program Locations 401 and 402
as 0.
A partitioned ICP-CC488 Control Panel
sends Open/Close Reports with Contact
ID Event Code 402.
sends Open/Close Reports with Contact
ID Event Code 402.
15.14 Open/Close Reporting Options
Location
403
0
No Open/Close Reports allowed
1
Report to Receiver 1
2
Report to Receiver 2
4
Report to both Receiver 1 and Receiver 2
8
Report to Receiver 2 only if Receiver 1 fails
Location 403 is set by default to report only to
Receiver 1. You can select whether Open and Close
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
Receiver 1. You can select whether Open and Close
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
15.15 Codepad Duress Report
Location
404
Default
6
A Duress Report (Contact ID Event Code 121) is
sent to the base station receiver when 9 is added to
the end of any valid User Code used to disarm the
system. This alarm is always silent. A Duress Alarm
can be activated during Exit Time. In other words, if
the system is armed and then disarmed by adding 9
to the end of the User Code before Exit Time
expires, a Codepad Duress Report is transmitted.
Adding 9 to the end of a User Code when arming the
system does not cause a Duress Alarm.
sent to the base station receiver when 9 is added to
the end of any valid User Code used to disarm the
system. This alarm is always silent. A Duress Alarm
can be activated during Exit Time. In other words, if
the system is armed and then disarmed by adding 9
to the end of the User Code before Exit Time
expires, a Codepad Duress Report is transmitted.
Adding 9 to the end of a User Code when arming the
system does not cause a Duress Alarm.
If you want a 3 to activate a Codepad Duress Alarm
instead of 9, select Option 2 in Location 498 (refer to
Section 18.7 Consumer Options 3 on page 83).
instead of 9, select Option 2 in Location 498 (refer to
Section 18.7 Consumer Options 3 on page 83).
Restore Reports are not sent for this
event.
event.
If Codepad Duress Reports are not
required, program Location 404 as 0.
required, program Location 404 as 0.
15.16 Codepad Panic Report
Location
405 to 406
Location
Default
Tens digit
405
7
Units digit
406 15
A Panic Alarm Report (Contact ID Event Code 120)
is sent to the base station receiver when a user
presses either [1] and [3] or [STAY] and [AWAY] at
the same time. A Panic Alarm is audible, but you can
program the alarm as silent by selecting Option 1 in
Location 493 (refer to Section 18.2 System Options 2 on
page 81).
is sent to the base station receiver when a user
presses either [1] and [3] or [STAY] and [AWAY] at
the same time. A Panic Alarm is audible, but you can
program the alarm as silent by selecting Option 1 in
Location 493 (refer to Section 18.2 System Options 2 on
page 81).