Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 15.0
System Reporting Information
EN | 69
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
15.24 System Status – Low Battery
Report
Location
420 to 421
Location
Default
Tens digit
420
10
Units digit
421 1
A Battery Test Failure Report (Contact ID Event
Code 309) is sent to the base station receiver when
the system’s battery voltage falls below 11.2 VDC or
when a Dynamic Battery Test detects a low capacity
battery.
Code 309) is sent to the base station receiver when
the system’s battery voltage falls below 11.2 VDC or
when a Dynamic Battery Test detects a low capacity
battery.
The control panel continually monitors the battery
voltage. Refer to Section 3.13 Fault Descriptions on
page 18 for more information. A Dynamic Battery
Test is done every time the system is armed and
every 4 hours after the control panel is powered up.
voltage. Refer to Section 3.13 Fault Descriptions on
page 18 for more information. A Dynamic Battery
Test is done every time the system is armed and
every 4 hours after the control panel is powered up.
I
f Low Battery Reports are not required,
program Locations 420 and 421 as 0.
15.25 System Status – Low Battery
Restore Report
Location
422 to 423
Location
Default
Tens digit
422
10
Units digit
423 6
A Low Battery Restore Report is sent if the backup
battery is restored the next time the system is armed,
or when the next Dynamic Battery Test reports the
battery test is OK.
battery is restored the next time the system is armed,
or when the next Dynamic Battery Test reports the
battery test is OK.
If Low Battery Restore Reports are not
required, program Locations 422 and 423
as 0.
required, program Locations 422 and 423
as 0.
15.26 System Status – Access Denied
Location
424 to 426
Location
Default
Code Retry Limit
(0 = Unlimited)
(0 = Unlimited)
424 6
Tens Digit
425 7
Units Digit
426 12
An Access Denied Report (Contact ID Event Code
421) is sent to the base station receiver when the
number of incorrect code attempts equals the
number programmed in Location 424. An Access
Denied Alarm is audible, but you can program the
alarm as silent by selecting Option 8 in Location 493
(refer to Section 18.2 System Options 2 on page 81).
421) is sent to the base station receiver when the
number of incorrect code attempts equals the
number programmed in Location 424. An Access
Denied Alarm is audible, but you can program the
alarm as silent by selecting Option 8 in Location 493
(refer to Section 18.2 System Options 2 on page 81).
Restore Reports for this event are not
transmitted.
transmitted.
If Access Denied Reports are not
required, program Locations 424 and 425
as 0.
required, program Locations 424 and 425
as 0.
Code Retries
The Code Retries feature restricts the number of
times an invalid User Code can be entered in an
attempt to operate the system. Location 424 sets the
number of incorrect code attempts that causes an
alarm. When the number of incorrect code attempts
equals the number programmed in this location, the
system performs these actions:
• Activates the sirens, internal screamers, and
times an invalid User Code can be entered in an
attempt to operate the system. Location 424 sets the
number of incorrect code attempts that causes an
alarm. When the number of incorrect code attempts
equals the number programmed in this location, the
system performs these actions:
• Activates the sirens, internal screamers, and
strobes connected to the control panel. Select
Option 8 in Location 493 (refer to Section 18.2
System Options 2 on page 81) to change this alarm
to silent.
Option 8 in Location 493 (refer to Section 18.2
System Options 2 on page 81) to change this alarm
to silent.
• Shuts down all codepads connected to the
control panel and locks them out for the time
period programmed in Location 478 (refer to
Section 17.8 Codepad Lockout Time).
period programmed in Location 478 (refer to
Section 17.8 Codepad Lockout Time).
• Sends an Access Denied Report (Contact ID
Event Code 421) to the base station receiver.
Each time the system is armed or disarmed, the Code
Retries counter is reset. You can program the counter
to a value from 1 to 15. If you want the number of
incorrect code attempts to be unlimited, program a 0
in Location 424. In this case, the Access Denied
Report is never generated and the system does not
perform the three actions listed above. This function
works when the system is armed or disarmed.
Retries counter is reset. You can program the counter
to a value from 1 to 15. If you want the number of
incorrect code attempts to be unlimited, program a 0
in Location 424. In this case, the Access Denied
Report is never generated and the system does not
perform the three actions listed above. This function
works when the system is armed or disarmed.
15.27 System Status Reporting Options
Location
427
0
No report allowed
1
Report to Receiver 1
2
Report to Receiver 2
4
Report to both Receiver 1 and Receiver 2
8
Report to Receiver 2 only if Receiver 1 fails
Location 427 is set by default to report only to
Receiver 1. You can select whether System Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
Receiver 1. You can select whether System Status
Reports are sent to Receiver 1, Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or no
reporting.
15.28 Test Reporting Time
Location
428 to 434
Location
Default
Hour of day (tens digit)
428
0
Hour of day (units digit)
429 0
Minute of day (tens digit)
430 0
Minute of day (units digit)
431 0
Test Report (tens digit)
432
7
Test Report (units digit)
433 1
Repeat interval in days
434
0
A Test Report (Contact ID Event Code 602) is a
specific signal sent to the base station receiver and is
normally used to test the dialing and reporting
functions of the control panel.
specific signal sent to the base station receiver and is
normally used to test the dialing and reporting
functions of the control panel.