Digital Security Controls Ltd. 06GS30551 User Manual
10
GS3055-I
Priority
This section will allow you to select the operating priority of this Device: Interface (at default) or SMS Dialler/Contact ID
Communicator.
Communicator.
Pay-as-you-go Balance message
,
,
,
,
,
NOTE: The Manufacturer shall not assume responsibility for Pay-as-you-go credit services managed by
GSM Network Providers.
GSM Network Providers.
If you enable this option, an SMS text message — containing information provided by
the GSM Network
regarding the end-user’s
credit balance — will be sent to the first number in the Telephone Number list. Enter the number of telephone calls
(ContactID reports and/or outgoing SMS text messages) this Device must allow before checking the Pay-as-you-go balance.
(ContactID reports and/or outgoing SMS text messages) this Device must allow before checking the Pay-as-you-go balance.
Pay-As-You-Go Balance message - If you click on this button the application will open a window showing the remaining credit
balance (if this service is managed by your network provider), or a message indicating that this service is not available.
The default string in the 'Pay-As-You-Go Balance message' field (*123#) is supported by most major service providers.
balance (if this service is managed by your network provider), or a message indicating that this service is not available.
The default string in the 'Pay-As-You-Go Balance message' field (*123#) is supported by most major service providers.
Periodic message
This section will allow you to set up the Periodic message options.
Date of first Periodic message - Select the Date of the first Periodic message.
Time of the first Periodic message - Select the Time of the first Periodic message.
Interval - Enter the interval (DD-HH-MM) between each Periodic message. Accepted DAY values: 0 to 693.
,
,
,
,
,
ATTENTION: If Input Line 1 is assigned to Special functions (Column A), transmission of the Periodic
message will be subordinate to ‘Unbalance’ on Input Line 1 (refer to the ‘Special functions’ table). If this
occurs, the Date and Hour of the Periodic message will be irrelevant.
message will be subordinate to ‘Unbalance’ on Input Line 1 (refer to the ‘Special functions’ table). If this
occurs, the Date and Hour of the Periodic message will be irrelevant.
Outputs Page
This page will allow you to set up and control the outputs.
Output Settings
Polarity: select the polarity of the output: H-Normally Open L-Normally Closed.
For Land Line Trouble, GSM Trouble, etc.: select the events that will activate the outputs.
Reserved Output: If this option is selected, all other events assigned to the output in this section will be ignored. Select
this option, if the output concerned is to be used for Remote control purposes (refer to “Activating and Deactivating and
Remote Control Outputs”).
The following options will affect Reserved Outputs ONLY.
this option, if the output concerned is to be used for Remote control purposes (refer to “Activating and Deactivating and
Remote Control Outputs”).
The following options will affect Reserved Outputs ONLY.
Output Label - Type in the label (max. 8 characters) of the appliance (e.g. Gate) which is to be remote-controlled
via SMS.
via SMS.
Output feedback - Select the type of feedback signal (None, Ring or SMS) to be sent when the respective output
activates. If the Output Label field is empty, the SMS option will not be available.
activates. If the Output Label field is empty, the SMS option will not be available.
Monostab. - Under normal circumstances, these outputs hold active status until they receive a deactivation
command. If automatic deactivation is required, it will be necessary to program the ON Time (i.e. the time the output
will hold active status).
command. If automatic deactivation is required, it will be necessary to program the ON Time (i.e. the time the output
will hold active status).
ON Time (sec.) - Enter the required ON Time in seconds (accepted values 2 to 254 seconds). If the output has been
programmed as Monostable, this value will determine the amount of time the output will hold active status before
restoring to standby.
programmed as Monostable, this value will determine the amount of time the output will hold active status before
restoring to standby.
Access Code
Type in the code (maximum 4 alphanumeric characters) which will allow the user to control the outputs over-the-phone.
Contact ID Page
This page will allow you to set up the Contact ID function.