ademco 8DL6162RF User Manual
- 2 -
APPLICATION GUIDELINES FOR THE 6162RF
Table 4 – Application Guidelines
If… And…
Then…
This is the only
transceiver on
the system,
transceiver on
the system,
You want to use both
the receiver and
transmitter function
on a single-partition
system,
the receiver and
transmitter function
on a single-partition
system,
•
Set the keypad to a device address assigned to the desired partition.*
•
Enable the receiver.
•
Program a system House ID in the control panel (this will enable the transmitter
function).**
function).**
•
Set the wireless devices that will communicate with this 6162RF to the same
system House ID.
system House ID.
There is another
receiver or
transceiver on
the system,
receiver or
transceiver on
the system,
You want to use only
the transmitter
function on a second
partition,
the transmitter
function on a second
partition,
•
Set the keypad to a device address assigned to the desired partition.*
•
Disable the receiver.
•
Program a DIFFERENT House ID in the 6162RF than is programmed in the control
panel.*/ **
panel.*/ **
•
Set the wireless devices that will communicate with this 6162RF to the same
House ID as the 6162RF.
House ID as the 6162RF.
You want to use only
the transmitter
function on a single-
partition system,
the transmitter
function on a single-
partition system,
•
Set the keypad to a device address assigned to the Partition 1.
•
Disable the receiver.
•
Program a House ID in the 6162RF that matches the system House ID
programmed in the control panel.*
programmed in the control panel.*
•
Set the wireless devices that will communicate with this 6162RF to the same
House ID.
House ID.
Notes:
* On VISTA-40 panels and above, wireless keypads (e.g., 5828) can only be used on a single partition. This partition is programmed in field 1*48,
and must match the partition assigned to the 6162RF. Wireless keys can be used on more than one partition, using a House ID programmed in the
6162RF and the devices. In this case, the wireless keys must be assigned to the same partition as the 6162RF.
* On VISTA-40 panels and above, wireless keypads (e.g., 5828) can only be used on a single partition. This partition is programmed in field 1*48,
and must match the partition assigned to the 6162RF. Wireless keys can be used on more than one partition, using a House ID programmed in the
6162RF and the devices. In this case, the wireless keys must be assigned to the same partition as the 6162RF.
** On VISTA-20P panels, the 6162RF will use the House ID programmed in the panel for the partition to which it is assigned. Wireless keypads can
only be used on Partition 1.
only be used on Partition 1.
4. PROGRAM
Refer to the following procedure to program the 6162RF:
Table 5 – 6162RF Programming
STEP DESCRIPTION
DISPLAY
CHOICES
1.
Enter Programming Mode: Within 60 seconds of power up, press and hold down the
and
keys at the
same time for 3 seconds.
2.
Keypad Address. The keypad address appears (Default = 16). Enter
a two-digit keypad address. Press the
a two-digit keypad address. Press the
key to continue.
Notes: – Refer to the control panel’s installation instructions for the
acceptable keypad addresses.
CON ADDR = 16
00-31
3.
Receiver Enable. Enter [1] to enable, or [0] to disable the receiver.
Press
Press
to continue.
RECEIVER
ON [0= OFF]
1 = ON
0 = OFF
4.
Receiver Address. If the receiver is enabled, enter the two-digit
receiver address. (00-30).
receiver address. (00-30).
Note: Refer to the control panel’s installation instructions for the acceptable
receiver addresses.
Press
to continue.
REC ADDR = 00
00-30
5.
User Code. Enter a valid four-digit user code to enable single button
arming keys. The user code must be programmed in the control.
arming keys. The user code must be programmed in the control.
Press
to continue.
USER CODE : ****
0000-9999