ademco 8DL6162RF User Manual
- 3 -
Table 5 – 6162RF Programming (continued)
STEP DESCRIPTION
DISPLAY
CHOICES
6.
House ID. This prompt will only appear if the receiver is disabled. If the
receiver is enabled the 6162RF will use the House ID programmed in
the panel. Refer to Application Guidelines section when selecting a
House ID.
To program a House ID: Enter 01-31
To disable the transmitter: Enter 00
receiver is enabled the 6162RF will use the House ID programmed in
the panel. Refer to Application Guidelines section when selecting a
House ID.
To program a House ID: Enter 01-31
To disable the transmitter: Enter 00
Note: Each device that will receive status from the 6162RF must be set to the
same House ID as the 6162RF (refer to Application Guidelines section).
Press
to continue.
HOUSE ID = XX
01-31
00 = Disable
Transmitter
Transmitter
7.
Enable High Security Mode. Enter [1] to select High Security Mode.
Note: If the High Security mode is enabled, the 6162RF will only recognize
encrypted devices.
If the High Security mode is disabled, the 6162RF will
process commands from both encrypted and non-encrypted devices.
Press
to continue.
HIGH SECURITY
OFF [1 = ON]
OFF [1 = ON]
1 = ON
(Enable)
(Enable)
0 = OFF
(Disable)
(Disable)
8.
Disable High Security Devices. Press the
key to skip this
prompt and exit Program Mode.
DISABLE HS DEV?
NO [1 = YES]
NO [1 = YES]
1 = YES
0 = NO
ACTIVATING HIGH SECURITY DEVICES
The procedure below should be followed when using High-Security (encrypted) devices.
Table 6 – Activating High Security Devices
STEP DESCRIPTION
1. Follow the normal procedure for programming the device into the control panel (refer to the Installation Instructions for
the device that you are programming). Exit out of Programming Mode.
2. Put the control panel in Go / No Go Test mode. (See the Installation Guide for the panel being installed.)
3. Follow the instructions supplied with each wireless device to enroll the device in High-security mode. After each device
is enrolled, the 6162RF will momentarily display “SECURITY DEVICE” along with the device number and its serial
number.
number.
Note: The 6162RF will support a maximum of 8 devices. If you attempt to enroll additional devices the keypad will display
“EXCEEDED NUMBER” “ALLOWED DEVICES”.
CHANGING USER CODE AND DISABLING HIGH SECURITY DEVICES
This mode gives you the ability to change the user code used to enable the single button arming keys and disable high security on
all wireless keys that have been enrolled in the 6162RF. The disable high security devices option is particularly useful if a user loses
a wireless key.
all wireless keys that have been enrolled in the 6162RF. The disable high security devices option is particularly useful if a user loses
a wireless key.
Once high-security (encrypted) devices have been disabled, they will only operate if the 6162RF is set to listen to both
encrypted and non-encrypted devices (programming step 6 in Table 5). To completely disable the devices, they must be
deleted from the control panel.
encrypted and non-encrypted devices (programming step 6 in Table 5). To completely disable the devices, they must be
deleted from the control panel.
Table 7 – Disabling High Security Devices
STEP DESCRIPTION
DISPLAY
CHOICES
1.
After the keypad has been powered for at least 60 seconds, press and
hold down the
hold down the
and
keys at the same time for 3 seconds.
The current keypad address will be displayed. (You cannot change the
keypad’s address at this point.) Press
keypad’s address at this point.) Press
to continue.
CON ADDRESS=XX
Programmed
Keypad
address
appears
Keypad
address
appears
2.
User Code. At the User Code prompt, enter the valid 4-digit user code
that will be used to enable the single button arming keys.. Press
that will be used to enable the single button arming keys.. Press
to continue.
USER CODE : ****
0000-9999
2.
Delete High Security Devices. Enter [1] to remove all high-security
(encrypted) devices. Press
(encrypted) devices. Press
to continue.
DELETE DEVICES?
NO [1 = YES]
NO [1 = YES]
1 = YES
0 = NO
3. If
YES
was selected in Step 2 the unit will display a confirm request to
delete the stored high security device. Enter [1] to accept and press
to exit the programming mode.
ARE YOU SURE?
NO [1 = YES]
NO [1 = YES]
1 = YES
0 = NO