ademco 8DL6162RF User Manual
TROUBLESHOOTING
The error messages listed in the following table cause the 6162RF to produce a single ding tone. The table describes the error
messages and the corrective actions.
messages and the corrective actions.
Table 8 – Troubleshooting
Display
Probable Cause
Corrective Action
Open Ckt
No data is being received from the control
panel.
panel.
Verify that the Yellow keypad wire is connected properly.
Check 100
RF Receiver
RF Receiver
Check 8xx*
1. The control panel does not see the
6162RF Receiver, or the Receiver is not
functioning.
functioning.
2. Another device on the keypad terminals
is conflicting with this receiver address.
1a. Verify that the Yellow and Green keypad wires are connected
properly.
1b. Verify that the receiver address is set for 00.
2. Verify the address of all devices on the keypad bus.
*xx= the device address of the receiver.
SPECIFICATIONS
Physical:
4.88"H x 6.934"W x 1.02"D
Displays:
4 x 16 alpha-numeric supertwist LCD, backlit.
Sounder:
Speaker [fire alarm is loud, pulsing single tone; (all Keypads) burglary alarm is loud, continuous, dual tone].
Voltage: 12VDC
(power-limited)
Current:
210mA (ARMED LED lit, LCD backlight and sounder on), reduces to 120mA when panel is operating in standby mode
(backlight off).
(backlight off).
NFPA-72:
Compliant.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires
the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires
the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch
circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT:
This device complies with Part 15 of the FCC
Rules, and RSS 210 of Industry Canada (IC).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Cet appareil est conforme à la partie 15 des règles
de la FCC & de RSS 210 des Industries Canada.
Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d'
interferences nuisibles. (2) Cet appareil doit accepter
toute interference reçue y compris les interferences
causant une reception indésirable.
This device complies with Part 15 of the FCC
Rules, and RSS 210 of Industry Canada (IC).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Cet appareil est conforme à la partie 15 des règles
de la FCC & de RSS 210 des Industries Canada.
Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d'
interferences nuisibles. (2) Cet appareil doit accepter
toute interference reçue y compris les interferences
causant une reception indésirable.
REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
WARRANTY INFORMATION: For the latest warranty information, please go to www.honeywell.com/security/hsc/resources/wa
DOCUMENTATION AND ONLINE SUPPORT: For the latest documentation and online support information, please go to:
http://www.security.honeywell.com/hsc/resources/MyWebTech
Ê800-11508+Š
800-11508 4/13 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2013 Honeywell International Inc.
www.honeywell.com/security