UTC Fire & Security Americas Corporation Inc 801-IXT2 User Manual
• Open
sensors
• Bypassed
sensors
The Status button blinks when an active alarm exists. The
Status button is lit when an abnormal condition such as a
trouble or open sensor exists in the system.
Status button is lit when an abnormal condition such as a
trouble or open sensor exists in the system.
You can clear certain status entries from the system (such
as old alarm history) by pressing Disarm after checking the
status.
as old alarm history) by pressing Disarm after checking the
status.
Touchpads and key fobs
You can use touchpads and key fobs to control the security
system from remote locations in and near your home.
Interfacing with the system using a touchpad is similar to
using the panel. Refer to the Simon XT TableTop User
Manual and the touchpad or key fob documentation for
details.
system from remote locations in and near your home.
Interfacing with the system using a touchpad is similar to
using the panel. Refer to the Simon XT TableTop User
Manual and the touchpad or key fob documentation for
details.
Status beeps
The panel sounds status beeps to alert you to various
system events and conditions as shown in Table 3 below.
system events and conditions as shown in Table 3 below.
Table 3: Status beeps
Activity Beep
response
Doors+Windows
Exit delay and entry delay beeps sound two times
every 5 seconds and two times per second during
the last 10 seconds.
every 5 seconds and two times per second during
the last 10 seconds.
Motions
Exit delay and entry delay beeps sound three times
every 5 seconds and three times per second during
the last 10 seconds.
every 5 seconds and three times per second during
the last 10 seconds.
Doors+Windows
and Motions
and Motions
Exit delay and entry delay beeps sound four times
every 5 seconds and four times per second during
the last 10 seconds.
every 5 seconds and four times per second during
the last 10 seconds.
Disarm One
beep.
Chime Two
beeps.
Special chime
Three beeps.
Trouble beeps
Six beeps every minute. Press Status to stop beeps
for 4 hours.
for 4 hours.
No activity beeps Twenty beeps every minute for 5 minutes (feature
must be programmed by the installer).
Alarm sirens
Exterior and interior sirens make three different alarm
sounds on the premises, each indicating a different type of
alarm. Sirens are programmed by the installer to time out
and stop sounding after a specified time.
sounds on the premises, each indicating a different type of
alarm. Sirens are programmed by the installer to time out
and stop sounding after a specified time.
Table 4 below describes the siren sounds used by the
security system.
security system.
Table 4: Siren sounds
Function Fire
Intrusion
Emergency
Interior and
panel siren
panel siren
Temporal 3
Steady
Fast on/off
Exterior siren
Temporal 3
Steady
Note:
Temporal 3 refers to a continuous pattern of three
siren pulses, then off for 1.5 seconds, three siren pulses,
then off for 1.5 seconds.
then off for 1.5 seconds.
Panel indicator lights
Table 5 below describes the front panel indicator lights.
Table 5: Indicator light
Button
When button light is on When button flashes
Doors+Windows Doors
and
windows
armed
Doors and windows
armed and no entry
delay on
armed and no entry
delay on
Motions Motions
armed Motion
sensors
armed and latchkey
on
on
Disarm
System disarmed
System subdisarmed
Status
System trouble, open
sensor, or bypassed
sensor
sensor, or bypassed
sensor
System in alarm
Enter
There are no open
sensors
sensors
Chime (solid bell)
Door will cause chime
Special chime
(outlined bell)
(outlined bell)
Motion will cause chime
Latchkey on (key) Latchkey feature on
Trouble beeps
Your security system is able to automatically test itself for:
• Power
failures
• Low
batteries
• Nonworking
sensors
• Communication trouble with the central monitoring
station
When your system detects one of the problems above, six
rapid beeps sound every minute until the trouble condition
is corrected. To stop the trouble beeps, press Status or arm
and then disarm the system while the trouble condition
exists. Trouble beeps will resume 4 hours later unless the
trouble condition is corrected. Refer to your Simon XT
TableTop User Manual for details.
rapid beeps sound every minute until the trouble condition
is corrected. To stop the trouble beeps, press Status or arm
and then disarm the system while the trouble condition
exists. Trouble beeps will resume 4 hours later unless the
trouble condition is corrected. Refer to your Simon XT
TableTop User Manual for details.
Simon XT TableTop Quick Operation Guide
3