Biolog-id SSTABIOLOGID User Manual
Smart Storage Agitator User Manual
Version: 1.0
Validation date of the manual: 18/09/2018
21 of 27
Recommended separation distances between mobile phone and RF communications equipment
and the PRD-7150300A
The PRD-7150300A is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or user of the PRD-7150300A may help prevent electromagnetic interference by maintaining a
minimum distance between the portable and mobile RF communications device (transmitters) and the PRD-7150300A, as
recommended below, according to the maximum transmit power of the communications apparatus.
controlled. The customer or user of the PRD-7150300A may help prevent electromagnetic interference by maintaining a
minimum distance between the portable and mobile RF communications device (transmitters) and the PRD-7150300A, as
recommended below, according to the maximum transmit power of the communications apparatus.
Maximum power output
assigned to the transmitter
W
Separation distance according to the frequency of the transmitter
150 kHz to 80 MHz
d = √ P 1.17
80 MHz to 800 MHz
d = √ P 1.17
800 MHz to 2.5 GHz
d = √ P 2.34
0.01
0.1
0.37M
0.37M
0,74m
1
10
100
For transmitters whose rated maximum transmit power is not given above, the recommended separation distance d in
meters (m) can be estimated using the frequency equation for the transmitter, where P is the maximum transmit power
characteristic of the transmitter in watts (W), depending on the manufacturer of the latter.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by the absorption and
reflection of structures, objects and people.
meters (m) can be estimated using the frequency equation for the transmitter, where P is the maximum transmit power
characteristic of the transmitter in watts (W), depending on the manufacturer of the latter.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by the absorption and
reflection of structures, objects and people.
The PRD-7150300A uses the 13.56 MHz frequency.
The frequency band is 13.553 - 13.567Mhz in accordance with ISO 15693. The modulation is
of the ASK type, the RF mode is TX / RX.
The apparent power is 100mW.
4.3. Cons-indications
As a prevention, it is advisable for people with a pacemaker not to use the SST-A.
4.4. Warning for users in United States
Federal Communication Commission Interference
Statement 47 CFR Section 15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.