Electronica Clarion S.A. de C.V. MD-5XR User Manual
pressing HANG UP button for less than one second, the LCD show message “CALL
END” and the radio will return to previous mode.
Press more than 2 seconds (17) answer button, Bluetooth icon blinks and LCD
LCD will show the message “PAIR CANC”, and the pairing process are cancel.
In order to connect any BT device to the radio, this device needs to be paired, this
BLUETOOTH
This radio has the Bluetooth tecnology embedded to its circuitry to enable Cellular
Phone Hands Free functionality (HFP) and has the Advanced Audio Distribution
Profile (A2DP.)
Phone Hands Free functionality (HFP) and has the Advanced Audio Distribution
Profile (A2DP.)
Receiving a call
The user can make a call from radio (if BT cell phone is connected), can be used
If press the power button whill in a call, the radio, before turning off, will disconnect
redial function, voice recognition (only if cell phone has this feature), or can select a
the BT connection and switch the call to the mobile.
phone number from cell phone address book, when cell phone start the dial (independently
If the ignition signal is turned off, the radio will continue ON until the phone call ends.
of dialing option) the dialing tone is heard in speakers, and the LCD show message
"BT TEL" during a call.
"BT TEL" during a call.
When receive a call the ring tone shall be heard on speakers (if ring tone is available
from cell phone), and the LCD show message “CALL IN”, followed by calling identi-
fication number (ID), in order to accept the call, the user will press Answer button
(on radio) less than 1 second, or respective answer button on cell phone itself.
After that, the current audio source will be muted and switched to audio of incoming call.
During a call, the LCD show message “BT TEL”, the user can finish a call, at any time
from cell phone), and the LCD show message “CALL IN”, followed by calling identi-
fication number (ID), in order to accept the call, the user will press Answer button
(on radio) less than 1 second, or respective answer button on cell phone itself.
After that, the current audio source will be muted and switched to audio of incoming call.
During a call, the LCD show message “BT TEL”, the user can finish a call, at any time
17
Making a call
radio.
show message “PAIRING” this message is followed by code pairing “KEY XXXX”
when the radio is found by Bluetooth device, it should identify it as “Chevrolet”, and
the cell phone request the code, insert this code (XXXX) on Bluetooth devices, follow
the instructions for connect, when all process is finished the radio show message
“BT CONNECT” and the name of Bluetooth device “NAME”, or “BT MOBILE” this
indicate that pairing process is ok. If this process is not complete after 3 minutes the
indicate that pairing process is ok. If this process is not complete after 3 minutes the
pairing process allows the device to identify and remember how to connect to the
17
Receiving and Making a Call
PAIRING A BLUETOOTH DEVICE / ANSWER OR MAKING A CALL
16
Usted podrá encender su radio por 20 minutos teniendo ACC apagado, presione la
perilla de volumen por más de 2 seg., hasta que aparezca en el display la leyenda
perilla de volumen por más de 2 seg., hasta que aparezca en el display la leyenda
BT ON, presione nuevamente hasta que aparezca IGNIT ON, gire la perilla para
Selección de 20 minutos encendido sin ACC (20 minutos ON)
2
15
REDUCIR A 128 mm.
ARTWORK Nº 982-11XX-XX
REDUCIR A 128 mm.
ARTWORK Nº 982-11XX-XX
30
ENGLISHENGLISHENGLISH
ESP
AÑOL
Con IGNIT ON, al apagar ACC el radio se apagará, pero puede encenderlo
Seleccionar entre IGNIT ON o IGNIT OFF.
El radio funcionará de la siguiente manera:
presionando el botón de PWR, el display mostrará la leyenda 20 min ON y
permanecerá encendido por 20 minutos, posteriormente se apagará.
permanecerá encendido por 20 minutos, posteriormente se apagará.
Con IGNIT OFF al apagar ACC el radio permanecerá encendido por 20 minutos
y posteriormente se apagará.
y posteriormente se apagará.
despliega estos cambios en el siguiente orden:
FM1
FM2
FM3
AM1
AM2
FM1
→ → → → →
Sintonía Manual:
Para seleccionar manualmente la estación de radio, presione el botón 15 por más
de 2 seg., hasta que el display muestre la leyenda “MANUAL” para sintonizar la
de 2 seg., hasta que el display muestre la leyenda “MANUAL” para sintonizar la
frecuencia en forma ascendente, o presione el botón 15 para sintonizar en forma
descendente, continúe presionando el botón para sintonizar en la dirección señalada
rápidamente, el modo manual se desactivará aproximadamente 5 seg., después del último
ajuste apareciendo la leyenda AUTO .
“
”
Boton de sintonización manual y automática ( / ):
15
La banda de sintonía cambiará cada vez que se presione este botón, el
indicador
Botón selector de banda de sintonía (AM/FM):
5
RADIO
Sintonización Automatica:
Presione los botones
para sintonizar en la dirección señalada, el
display mostrará la leyenda “SEARCH” e iniciará la búsqueda de la siguiente
frecuencia con señal, al encontrarla se detendrá e iniciará la reproducción de
manera automática, la función de búsqueda automática también puede ser
detenida presionando este botón nuevamente ó activando cualquier otra función.
frecuencia con señal, al encontrarla se detendrá e iniciará la reproducción de
manera automática, la función de búsqueda automática también puede ser
detenida presionando este botón nuevamente ó activando cualquier otra función.
( ) 15 ( ),