User ManualTable of ContentsOmni.Net Lite1Copyright3Federal Communications Commission (FCC) Interference Statement4Safety Warnings5ZyXEL Limited Warranty6Customer Support7Table of Contents9List of Figures13List of Tables15Preface171. Introduction191.1 About your TA191.1.1 TA Features191.1.1.1 ISDN Basic Rate Interface (BRI) Support191.1.1.2 Extensive Analog Phone Support191.1.1.3 Outgoing Data Call Bumping Support191.1.1.4 PPP Multilink191.1.1.5 Bandwidth-On-Demand201.1.1.6 PAP and CHAP Security201.1.1.7 Upgrade Firmware201.1.1.8 Supplementary Voice Features201.1.1.9 Switch Type201.1.2 TA and ISDN Interfaces201.2 TA Hardware and Driver Installation211.3 Top Panel LEDs211.4 Configuration Methods222. Using the Utility252.1 Accessing the TA with the Utility252.2 Navigating the Utility272.3 System282.4 RS-232 Port: Local DN (Directory Number) and Call Type292.4.1 Introduction to PPP292.4.2 Multilink PPP (MP or MLP)302.4.3 BACP and BAP302.4.4 ISDN Protocols312.4.5 Configuring Local DN and Call Type312.5 RS-232 Port: PPP/MP Parameters332.5.1 Link Authentication332.5.1.1 Windows Authentication332.5.2 Call Bumping (Bandwidth Release) for Voice Calls352.5.3 Bandwidth On Demand (BOD)352.5.4 Configuring PPP/MP Parameters362.6 RS-232 Port: V.24 Signal372.6.1 RS-232 Flow Control372.6.2 Configuring V.24 Signal382.7 Incoming Call Screening392.8 Outgoing Call Screening402.9 Pre-stored Numbers412.10 RS-232 Port: Advance Setting422.11 Analog Port: Local DN and Options442.11.1 MSN (Multiple Subscriber Number) and Subaddress442.11.1.1 Phone Number Assignment Example442.11.2 Caller ID452.11.2.1 Type 1: On-hook Caller ID Transmission452.11.2.2 Type 2: Off-hook Caller ID Transmission452.11.3 Dialing Method462.11.4 Configuring Local DN and Options462.12 Voice Calls472.12.1 Placing a Voice Call472.12.2 Answering a Voice Call482.12.3 Intercom482.12.4 Supplementary Services482.12.4.1 The Flash Key492.12.4.2 Call Hold492.12.4.3 Call Waiting502.12.4.4 Call Transfer512.12.4.5 Three-Way Conference523. Using AT Commands533.1 AT Commands Overview533.2 Accessing the TA Example533.3 AT Commands563.3.1 Data Command Sets563.3.2 Command Sets for Analog Ports603.3.3 Debug Command Sets623.4 Configuring Examples with AT Commands623.4.1 Phone Number Assignment633.4.2 Storing Phone Number633.4.3 Setting Ports Priority643.4.4 Disabling Call Waiting643.4.5 Link Authentication643.4.6 Call Bumping (Bandwidth Release) for Voice Calls653.4.7 Bandwidth On Demand (BOD)653.4.8 Incoming Call Screening653.4.8.1 Data Call653.4.8.2 Voice Call663.4.9 Outgoing Call Screening663.4.9.1 Data Call663.4.9.2 Voice Call663.4.10 Caller ID663.5 Result Codes674. Using Tone Commands694.1 How to Use Tone Commands with a Telephone Keypad694.1.1 Tone and Ring Patterns694.2 Tone Commands704.3 Configuring Example with Tone Commands714.3.1 Phone Number Assignment714.3.2 Storing Phone Number724.3.3 Setting Ports Priority724.3.4 Disabling Call Waiting724.3.5 Incoming Call Screening724.3.5.1 Voice Call724.3.6 Outgoing Call Screening724.3.6.1 Voice Call724.3.7 Caller ID725. Firmware Upgrade735.1 Upgrading Using the Utility735.2 Upgrading Using HyperTerminal Example746. Troubleshooting79Index81Numerics81A81B81C81D81E82F82G82H82I82L82M82N82O82P82Q83R83S83T83U83V83W83X84Z84Size: 2.12 MBPages: 84Language: EnglishOpen manual