Cisco Cisco ONS 15454 M12 Multiservice Transport Platform (MSTP) Guía De Instalación
10
Installing Cisco ONS 15454 SONET/SDH XC-VXC-10G Cards
78-17123-01
Install the XC-VXC-10G Cards
Note
If the FAIL LED is lit continuously on the TCC2/TCC2P card, see the tip following step 6 about
the TCC2/TCC2P automatic upload.
the TCC2/TCC2P automatic upload.
Step 6
Verify that the ACT/STBY LED is green for active if this is the first powered-up TCC2/TCC2P card
installed, or yellow for standby if this is the second powered-up TCC2/TCC2P. The IP address,
temperature of the node, and time of day appear on the LCD. The default time and date is 12:00 AM,
January 1, 1970.
installed, or yellow for standby if this is the second powered-up TCC2/TCC2P. The IP address,
temperature of the node, and time of day appear on the LCD. The default time and date is 12:00 AM,
January 1, 1970.
Step 7
The LCD cycles through the IP address, node name, and software version. Verify that the correct
software version displays on the LCD.
software version displays on the LCD.
Tip
If you install a standby TCC2/TCC2P card that has a different software version than the active TCC card,
the newly installed standby TCC2/TCC2P card automatically copies the software version from the active
TCC2/TCC2P card. You do not need to do anything in this situation. However, the loading TCC2/TCC2P
card does not boot up in the normal manner. When the standby card is first inserted, the LEDs follow
most of the sequence listed in
the newly installed standby TCC2/TCC2P card automatically copies the software version from the active
TCC2/TCC2P card. You do not need to do anything in this situation. However, the loading TCC2/TCC2P
card does not boot up in the normal manner. When the standby card is first inserted, the LEDs follow
most of the sequence listed in
. After the red FAIL LED turns on for about 5 seconds, the FAIL
Table 3
LED Activity during TCC2/TCC2P and XC-VXC-10G Card Installation
Card Type
LED Activity
TCC2/TCC2P
1.
All LEDs turn on briefly.
2.
The red FAIL LED, the yellow ACT/STBY LED, the red REM LED, the
green SYNC LED, and the green ACO LED turn on for about 10 seconds.
green SYNC LED, and the green ACO LED turn on for about 10 seconds.
3.
The red FAIL LED and the green ACT/STBY LED turn on for about 40
seconds.
seconds.
4.
The red FAIL LED blinks for about 10 seconds.
5.
The red FAIL LED turns on for about 5 seconds.
6.
The red FAIL LED blinks for about 5 seconds and then becomes solid.
7.
All LEDs (including the CRIT, MAJ, MIN, REM, SYNC, and ACO
LEDs) blink once and turn off for about 10 seconds.
LEDs) blink once and turn off for about 10 seconds.
8.
Both green PWR LEDs turn on for 5 seconds. The PWR LEDs then turn
red for 2 to 3 minutes before going to steady green.
red for 2 to 3 minutes before going to steady green.
9.
The yellow ACT/STBY turns on and the PWR LEDs turn red for 2 to 3
minutes. (The Sync LED might be green at this time.)
minutes. (The Sync LED might be green at this time.)
10.
The yellow ACT/STBY LED turns on. (The ACT/STBY LED might take
several minutes to turn on while the TCC processor boots.)
several minutes to turn on while the TCC processor boots.)
XC-VXC-10G
1.
The red LED turns on and remains lit for 20 to 30 seconds.
2.
The red LED blinks for 35 to 45 seconds.
3.
The red LED remains lit for 5 to 10 seconds.
4.
All LEDs blink once and turn on.
5.
The ACT/STBY LED turns on.