Galil DMC-1700 Manual De Usuario
44 • Chapter 3 Connecting Hardware
DMC-1700/1800
_LFx or MG _LFx. This prints the value of the limit switch operands for the ‘x’ axis. The logic state of the limit
switches can also be interrogated with the TS command. For more details on TS see the Command Reference.
switches can also be interrogated with the TS command. For more details on TS see the Command Reference.
Home Switch Input
Homing inputs are designed to provide mechanical reference points for a motion control application. A transition in
the state of a Home input alerts the controller that a particular reference point has been reached by a moving part in
the motion control system. A reference point can be a point in space or an encoder index pulse.
the state of a Home input alerts the controller that a particular reference point has been reached by a moving part in
the motion control system. A reference point can be a point in space or an encoder index pulse.
The Home input detects any transition in the state of the switch and toggles between logic states 0 and 1 at every
transition. A transition in the logic state of the Home input will cause the controller to execute a homing routine
specified by the user.
transition. A transition in the logic state of the Home input will cause the controller to execute a homing routine
specified by the user.
There are three homing routines supported by the DMC-1700/1800: Find Edge (FE), Find Index (FI), and Standard
Home (HM).
Home (HM).
The Find Edge routine is initiated by the command sequence: FEX <return>, BGX <return>. The Find Edge routine
will cause the motor to accelerate, then slew at constant speed until a transition is detected in the logic state of the
Home input. The direction of the FE motion is dependent on the state of the home switch. High level causes
forward motion. The motor will then decelerate to a stop. The acceleration rate, deceleration rate and slew speed
are specified by the user, prior to the movement, using the commands AC, DC, and SP. It is recommended that a
high deceleration value be used so the motor will decelerate rapidly after sensing the Home switch.
will cause the motor to accelerate, then slew at constant speed until a transition is detected in the logic state of the
Home input. The direction of the FE motion is dependent on the state of the home switch. High level causes
forward motion. The motor will then decelerate to a stop. The acceleration rate, deceleration rate and slew speed
are specified by the user, prior to the movement, using the commands AC, DC, and SP. It is recommended that a
high deceleration value be used so the motor will decelerate rapidly after sensing the Home switch.
The Find Index routine is initiated by the command sequence: FIX <return>, BGX <return>. Find Index will cause
the motor to accelerate to the user-defined slew speed (SP) at a rate specified by the user with the AC command and
slew until the controller senses a change in the index pulse signal from low to high. The motor then decelerates to a
stop at the rate previously specified by the user with the DC command. Although Find Index is an option for
homing, it is not dependent upon a transition in the logic state of the Home input, but instead is dependent upon a
transition in the level of the index pulse signal.
the motor to accelerate to the user-defined slew speed (SP) at a rate specified by the user with the AC command and
slew until the controller senses a change in the index pulse signal from low to high. The motor then decelerates to a
stop at the rate previously specified by the user with the DC command. Although Find Index is an option for
homing, it is not dependent upon a transition in the logic state of the Home input, but instead is dependent upon a
transition in the level of the index pulse signal.
The Standard Homing routine is initiated by the sequence of commands HMX <return>, BGX <return>. Standard
Homing is a combination of Find Edge and Find Index homing. Initiating the standard homing routine will cause
the motor to slew until a transition is detected in the logic state of the Home input. The motor will accelerate at the
rate specified by the command, AC, up to the slew speed. After detecting the transition in the logic state on the
Home Input, the motor will decelerate to a stop at the rate specified by the command, DC. After the motor has
decelerated to a stop, it switches direction and approaches the transition point at the speed of 256 counts/sec. When
the logic state changes again, the motor moves forward (in the direction of increasing encoder count) at the same
speed, until the controller senses the index pulse. After detection, it decelerates to a stop and defines this position as
0. The logic state of the Home input can be interrogated with the command MG _HMX. This command returns a 0
or 1 if the logic state is low or high, respectively. The state of the Home input can also be interrogated indirectly
with the TS command.
Homing is a combination of Find Edge and Find Index homing. Initiating the standard homing routine will cause
the motor to slew until a transition is detected in the logic state of the Home input. The motor will accelerate at the
rate specified by the command, AC, up to the slew speed. After detecting the transition in the logic state on the
Home Input, the motor will decelerate to a stop at the rate specified by the command, DC. After the motor has
decelerated to a stop, it switches direction and approaches the transition point at the speed of 256 counts/sec. When
the logic state changes again, the motor moves forward (in the direction of increasing encoder count) at the same
speed, until the controller senses the index pulse. After detection, it decelerates to a stop and defines this position as
0. The logic state of the Home input can be interrogated with the command MG _HMX. This command returns a 0
or 1 if the logic state is low or high, respectively. The state of the Home input can also be interrogated indirectly
with the TS command.
For examples and further information about Homing, see command HM, FI, FE of the Command Reference and the
section entitled ‘Homing’ in the Programming Motion Section of this manual
section entitled ‘Homing’ in the Programming Motion Section of this manual
.
Abort Input
The function of the Abort input is to immediately stop the controller upon transition of the logic state.
NOTE: The response of the abort input is significantly different from the response of an activated limit switch.
When the abort input is activated, the controller stops generating motion commands immediately, whereas the limit
switch response causes the controller to make a decelerated stop.
When the abort input is activated, the controller stops generating motion commands immediately, whereas the limit
switch response causes the controller to make a decelerated stop.
NOTE: The effect of an Abort input is dependent on the state of the off-on-error function for each axis. If the Off-
On-Error function is enabled for any given axis, the motor for that axis will be turned off when the abort signal is
generated. This could cause the motor to ‘coast’ to a stop since it is no longer under servo control. If the Off-On-
Error function is disabled, the motor will decelerate to a stop as fast as mechanically possible and the motor will
remain in a servo state.
On-Error function is enabled for any given axis, the motor for that axis will be turned off when the abort signal is
generated. This could cause the motor to ‘coast’ to a stop since it is no longer under servo control. If the Off-On-
Error function is disabled, the motor will decelerate to a stop as fast as mechanically possible and the motor will
remain in a servo state.