Friedrich 920-087-09 ユーザーズマニュアル

TABLE 2

Model

Heater kW

Power Cord Kit

Voltage

Amperage

Receptacle

PDE07K

0.0

PXPC23000

230/208

NEMA 6-15r

PDE/PDH07K

2.0

PXPC23015

230/208

NEMA 6-15r

3.0

STD

230/208

NEMA 6-20r

PDE09K

0.0

PXPC23000

230/208

NEMA 6-15r

PDE/PDH09K

2.0

PXPC23015

230/208

NEMA 6-15r

3.0

STD

230/208

NEMA 6-20r

5.0

PXPC23030

230/208

NEMA 6-30r

PDE12K

0.0

PXPC23000

230/208

NEMA 6-15r

PDE/PDH12K

2.0

PXPC23015

230/208

NEMA 6-15r

3.0

STD

230/208

NEMA 6-20r

5.0

PXPC23030

230/208

NEMA 6-30r

PDE15K

0.0

PXPC23000

230/208

NEMA 6-15r

PDE/PDH15K

2.0

PXPC23015

230/208

NEMA 6-15r

3.0

PXPC23020

230/208

NEMA 6-20r

5.0

STD

230/208

NEMA 6-30r

PDE/PDH07R

2.0

PXPC26515

265

NEMA 6-15r

3.0

STD

265

NEMA 6-20r

PDE/PDH09R

2.0

PXPC26515

265

NEMA 6-15r

3.0

STD

265

NEMA 6-20r

5.0

PXPC26530

265

NEMA 6-30r

PDE/PDH12R

2.0

PXPC26515

265

NEMA 6-15r

3.0

STD

265

NEMA 6-20r

5.0

PXPC26530

265

NEMA 6-30r

PDE/PDH15R

2.0

PXPC26515

265

NEMA 6-15r

3.0

PXPC26520

265

NEMA 6-20r

5.0

STD

265

NEMA 6-30r

Electrical Wiring for 265 Volt

Models

NOTE:

It is recommended that the PXSB subbase assembly, the

PXCJA conduit kit (or equivalent) be installed on all hardwire

units. If installing a flush-floor mounted unit, make sure the

chassis can be removed from the sleeve for service and

maintenance.

WARNING

Electrical Shock Hazard

Turn off electrical power before service

or installation.

ALL electrical connections and wiring

MUST be installed by a qualified

electrician and conform to the National

Code and all local codes which have

jurisdiction.

Failure to do so can result in property

damage, personal injury and/or death.

Power Cord Installation

All 265V PTAC/PTHP units come with a factory installed non-LCDI

power cord for use in a subbase. If the unit is to be hard-wired refer to

the instructions below.

To install the line voltage power leads and conduit

to chassis, follow the instructions below and refer

to Figures 25-27 on page 19. PXCJA Conduit Kit

is required with this setup.

1. Follow the removal process of the chassis’s junction box

(Figure 25, step 2, page 19).

2. Prepare the 265V (or 230V) power cord for connection to the chas-

sis’ power cord connector by cutting the cord to the appropriate

length (refer to Figure 26 and follow Figure 15). Power cord harness

selection shown on Table 2 on page 14.